DP83848J_07 NSC [National Semiconductor], DP83848J_07 Datasheet - Page 17
DP83848J_07
Manufacturer Part Number
DP83848J_07
Description
Manufacturer
NSC [National Semiconductor]
Datasheet
1.DP83848J_07.pdf
(78 pages)
- Current page: 17 of 78
- Download datasheet (2Mb)
2.3 PHY ADDRESS
The 5 PHY address inputs pins are shared with the
RXD[3:0] pins and COL pin as shown below.
The DP83848J can be set to respond to any of 32 possible
PHY addresses via strap pins. The information is latched
into the PHYCR register (address 19h, bits [4:0]) at device
power-up and hardware reset. The PHY Address pins are
shared with the RXD and COL pins. Each DP83848J or
port sharing an MDIO bus in a system must have a unique
physical address.
The DP83848J supports PHY Address strapping values 0
(<00000>) through 31 (<11111>). Strapping PHY Address
0 puts the part into Isolate Mode. It should also be noted
that selecting PHY Address 0 via an MDIO write to PHYCR
will not put the device in Isolate Mode. See Section 2.3.1
for more information.
For further detail relating to the latch-in timing requirements
of the PHY Address pins, as well as the other hardware
configuration pins, refer to the Reset summary in
Section 6.0.
Pin #
35
36
37
38
39
Table 2. PHY Address Mapping
PHYAD Function
PHYAD0
PHYAD1
PHYAD2
PHYAD3
PHYAD4
RXD Function
Figure 2. PHYAD Strapping Example
RXD_0
RXD_1
RXD_2
RXD_3
COL
17
Since the PHYAD[0] pin has weak internal pull-up resistor
and PHYAD[4:1] pins have weak internal pull-down resis-
tors, the default setting for the PHY address is 00001
(01h).
Refer to Figure 2 for an example of a PHYAD connection to
external components. In this example, the PHYAD strap-
ping results in address 00011 (03h).
2.3.1 MII Isolate Mode
The DP83848J can be put into MII Isolate mode by writing
to bit 10 of the BMCR register or by strapping in Physical
Address 0. It should be noted that selecting Physical
Address 0 via an MDIO write to PHYCR will not put the
device in the MII isolate mode.
When in the MII isolate mode, the DP83848J does not
respond to packet data present at TXD[3:0], TX_EN inputs
and presents a high impedance on the TX_CLK, RX_CLK,
RX_DV, RX_ER, RXD[3:0], COL, and CRS outputs. When
in Isolate mode, the DP83848J will continue to respond to
all management transactions.
While in Isolate mode, the PMD output pair will not transmit
packet data but will continue to source 100BASE-TX
scrambled idles or 10BASE-T normal link pulses.
The DP83848J can Auto-Negotiate or parallel detect to a
specific technology depending on the receive signal at the
PMD input pair. A valid link can be established for the
receiver even when the DP83848J is in Isolate mode.
VCC
www.national.com
Related parts for DP83848J_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Thin SOT23 1A Load Step-Down DC-DC Regulator
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
TRI-STATE Dual Receiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Hex MOS Drivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Quad High Current Peripheral Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
(RS-422/RS-423) Line Drivers with TRI-STATE Outputs
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Multipoint RS485/RS422 Transceivers/Repeaters
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Low Power EIA-RS-485 Transceiver with Sleep Mode
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
BTL Handshake Transceiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Octal 80-Bit Static Shift Register
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
PUSH BUTTON PULSE DIALER CIRCUITS
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Hex Schmitt Trigger with Extended Input Voltage
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Microprocessor Real Time Clock
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Dual Line Receivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
Part Number:
Description:
Dual TRI-STATE Differential Line Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet: