ISL6209 INTERSIL [Intersil Corporation], ISL6209 Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
ISL6209
Manufacturer Part Number
ISL6209
Description
High Voltage Synchronous Rectified Buck MOSFET Driver
Manufacturer
INTERSIL [Intersil Corporation]
Datasheet
1.ISL6209.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6209CB
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6209CBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Electrical Specifications
NOTE:
Functional Pin Description
UGATE (Pin 1 for SOIC-8, Pin 8 for QFN)
The UGATE pin is the upper gate drive output. Connect to
the gate of high-side power N-Channel MOSFET.
BOOT (Pin 2 for SOIC-8, Pin 1 for QFN)
BOOT is the floating bootstrap supply pin for the upper gate
drive. Connect the bootstrap capacitor between this pin and
the PHASE pin. The bootstrap capacitor provides the charge
to turn on the upper MOSFET. See the Bootstrap Diode and
Capacitor section under DESCRIPTION for guidance in
choosing the appropriate capacitor value.
PWM (Pin 3 for SOIC-8, Pin 2 for QFN)
The PWM signal is the control input for the driver. The PWM
signal can enter three distinct states during operation, see the
three-state PWM Input section under DESCRIPTION for further
details. Connect this pin to the PWM output of the controller. In
addition, place a 500kΩ resistor to ground from this pin. This
allows for proper three-state operation under all start-up
conditions.
GND (Pin 4 for SOIC-8, Pin 3 for QFN)
GND is the ground pin. All signals are referenced to this
node.
LGATE (Pin 5 for SOIC-8, Pin 4 for QFN)
LGATE is the lower gate drive output. Connect to gate of the
low-side power N-Channel MOSFET.
VCC (Pin 6 for SOIC-8, Pin 5 for QFN)
Connect the VCC pin to a +5V bias supply. Place a high
quality bypass capacitor from this pin to GND.
OUTPUT
Upper Drive Source Resistance
Upper Driver Source Current (Note 5)
Upper Drive Sink Resistance
Upper Driver Sink Current (Note 5)
Lower Drive Source Resistance
Lower Driver Source Current (Note 5)
Lower Drive Sink Resistance
Lower Driver Sink Current (Note 5)
5. Guaranteed by design, not tested.
PARAMETER
5
Recommended Operating Conditions, Unless Otherwise Noted. (Continued)
SYMBOL
R
R
R
R
I
I
I
I
UGATE
UGATE
LGATE
LGATE
UGATE
UGATE
LGATE
LGATE
500mA Source Current
V
500mA Sink Current
V
500mA Source Current
V
500mA Sink Current
V
UGATE-PHASE
UGATE-PHASE
LGATE
LGATE
ISL6209
= 2.5V
= 2.5V
TEST CONDITIONS
DELAY (Pin 7 for SOIC-8, Pin 6 for QFN)
The DELAY pin sets the dead-time between gate switching
for the ISL6209. Connect a resistor to GND from this pin to
adjust the dead-time, refer to Figure 5. Tie this pin to VCC to
disable the delay circuitry. See Shoot-Through Protection
section for more detail.
PHASE (Pin 8 for SOIC-8, Pin 7 for QFN)
Connect the PHASE pin to the source of the upper MOSFET
and the drain of the lower MOSFET. This pin provides a
return path for the upper gate driver.
Description
Operation
Designed for speed, the ISL6209 dual MOSFET driver controls
both high-side and low-side N-Channel FETs from one
externally provided PWM signal.
A rising edge on PWM initiates the turn-off of the lower
MOSFET (see Timing Diagram). After a short propagation
delay [t
times [t
section. Adaptive shoot-through circuitry monitors the
LGATE voltage and determines the upper gate delay time
[t
drops below 1V. This prevents both the lower and upper
MOSFETs from conducting simultaneously, or shoot-
through. Once this delay period is completed, the upper gate
drive begins to rise [t
turns on.
= 2.5V
= 2.5V
PDHUGATE
PDLLGATE
FLGATE
], based on how quickly the LGATE voltage
] are provided in the Electrical Specifications
], the lower gate begins to fall. Typical fall
RUGATE
MIN
], and the upper MOSFET
-
-
-
-
-
-
-
-
TYP
1.0
2.0
1.0
2.0
1.0
2.0
0.4
4.0
MAX
2.5
2.5
2.5
1.0
-
-
-
-
UNITS
Ω
A
Ω
A
Ω
A
Ω
A