AT89S8252-24QC ATMEL [ATMEL Corporation], AT89S8252-24QC Datasheet - Page 26

• Manufacturer Part Number: AT89S8252-24QC
• Description: 8-bit Microcontroller with 8K Bytes Flash
• Manufacturer: ATMEL [ATMEL Corporation]

Z
Absolute Maximum Ratings*
DC Characteristics
The values shown in this table are valid for T
Notes:
26
Operating Temperature.................................. -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin
with Respect to Ground .....................................-1.0V to +7.0V
Maximum Operating Voltage ............................................ 6.6V
DC Output Current...................................................... 15.0 mA
Symbol
V
V
V
V
V
V
V
V
I
I
I
RRST
C
I
IL
TL
LI
CC
IL
IL1
IH
IH1
OL
OL1
OH
OH1
IO
1. Under steady state (non-transient) conditions, I
must be externally limited as follows:
Maximum I
Maximum I
Port 0: 26 mA
Ports 1, 2, 3: 15 mA
Parameter
Input Low-voltage
Input Low-voltage (EA)
Input Hifh-voltage
Input Hifh-voltage
Output Low-voltage
(Ports 1,2,3)
Output Low-voltage
(Port 0, ALE, PSEN)
Output Hifh-voltage
(Ports 1,2,3, ALE, PSEN)
Output Hifh-voltage
(Port 0 in External Bus Mode)
Logical 0 Input Current (Ports 1,2,3)
Logical 1 to 0 Transition Current (Ports 1,2,3)
Input Leakage Current
(Port 0, EA)
Reset Pull-down Resistor
Pin Capacitance
Power Supply Current
Power-down Mode
OL
OL
AT89S8252
per port pin: 10 mA
per 8-bit port:
(2)
(1)
(1)
A
= -40°C to 85°C and V
OL
Condition
(Except EA)
(Except XTAL1, RST)
(XTAL1, RST)
I
I
I
I
I
I
I
I
V
V
0.45 < V
Test Freq. = 1 MHz, T
Active Mode, 12 MHz
Idle Mode, 12 MHz
V
V
OL
OL
OH
OH
OH
OH
OH
OH
IN
IN
CC
CC
= 1.6 mA
= 3.2 mA
= -60 µA, V
= -25 µA
= -10 µA
= -800 µA, V
= -300 µA
= -80 µA
= 0.45V
= 2V, V
= 6V
= 3V
IN
< V
*NOTICE:
CC
= 5V ± 10%
CC
CC
CC
CC
= 5V ± 10%
2. Minimum V
= 5.0V ± 20%, unless otherwise noted.
= 5V ± 10%
A
Maximum total I
If I
related specification. Pins are not guaranteed to sink
current greater than the listed test conditions.
= 25°C
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
OL
exceeds the test condition, V
CC
0.2 V
for Power-down is 2V
0.75 V
0.75 V
0.7 V
0.9 V
0.9 V
OL
Min
-0.5
-0.5
2.4
2.4
CC
50
for all output pins: 71 mA
+ 0.9
CC
CC
CC
CC
CC
0.2 V
0.2 V
V
V
CC
CC
-650
OL
Max
±10
300
100
0.5
0.5
-50
6.5
10
25
40
CC
CC
+ 0.5
+ 0.5
may exceed the
- 0.1
- 0.3
Units
KΩ
mA
mA
µA
µA
µA
pF
µA
µA
V
V
V
V
V
V
V
V
V
V
V
V