TH3122KDF MELEXIS [Melexis Microelectronic Systems], TH3122KDF Datasheet
TH3122KDF
Related parts for TH3122KDF
TH3122KDF Summary of contents
Page 1
Features and Benefits K-Bus Transceiver: PNP-open emitter driver with slew rate control and current limitation BUS input voltage -24V ... 30V (independently of V ISO 9141 and ODBII compliant Possibility of BUS wake up Operating voltage V = 5.5 ... ...
Page 2
K-Bus Transceiver with integrated Voltage Regulator Functional Diagram VS EN VTR BUS SI 3901003122 Rev 004 Power Supply 7.8V +5V 6.8V Reset-Logic VTR-Logic OSC Wake-up V thH V thL Bus-Logic pnp Control slew rate foldback V THSI_H V THSI_L Figure ...
Page 3
K-Bus Transceiver with integrated Voltage Regulator Functional Description The TH3122 consists of a voltage regulator 5V/100mA and a K-Bus transceiver, which is a bi-directional bus interface device for data transfer between K-Bus and the K-Bus protocol controller. RxD VCC TxD ...
Page 4
K-Bus Transceiver with integrated Voltage Regulator Bit Compare If the signals at the pin TxD and the pin BUS within a specified time t are not identical, the bc transmission will be interrupted. If both signals at TxD and BUS ...
Page 5
K-Bus Transceiver with integrated Voltage Regulator VS V RESEIN VCC t Res RESET Figure 7 - Initialization The input EN has an internal pull down resistor. If EN=high, the internal pull down current is switched off to minimize the quiescent ...
Page 6
K-Bus Transceiver with integrated Voltage Regulator Application Hints Operating during Disturbances The absence GND connection or ground S CC shift either alone or in any combination, do not influence or disturb the communication between other bus ...
Page 7
K-Bus Transceiver with integrated Voltage Regulator Electrical Specification All voltages are referenced to ground (GND). Positive currents flow into the IC. The absolute maximum ratings given in the table below are limiting values that do not lead to a permanent ...
Page 8
K-Bus Transceiver with integrated Voltage Regulator Static Characteristics (V = 5.25 to 16V 4.75 to 5.25V Parameter Linear Regulator Output voltage VCC Supply current, „normal mode“ Supply current, „sleep mode“ Drop-out voltage Output current VCC ...
Page 9
K-Bus Transceiver with integrated Voltage Regulator Static Characteristics (continued) Parameter Comparator SI, SO Threshold low SI Threshold High SI Hysteresis Output voltage low at SO Pull-up current at SO Input VTR Threshold low Threshold high Output current low Output current ...
Page 10
K-Bus Transceiver with integrated Voltage Regulator Dynamic Characteristics (5.25V V 16V, 4.75V V 5.25V, -40° Parameter RESET Reset time Reset rising time K-Bus-Interface Slew rate BUS falling edge Slew rate BUS rising edge Symmetry of Slew rate BUS ...
Page 11
K-Bus Transceiver with integrated Voltage Regulator Pin Description Pin Name VTR 4 GND 5 GND 6 BUS SEN/STA 10 RxD 11 TxD 12 GND 13 GND 14 RESET 15 SENSE ...
Page 12
K-Bus Transceiver with integrated Voltage Regulator Mechanical Specifications DF (SOIC16) Package Dimensions Small Outline Integrated Circiut (SOIC), All Dimension in mm, coplanarity < 0 min 10.1 max 10.5 All Dimension in inch, coplanarity ...
Page 13
K-Bus Transceiver with integrated Voltage Regulator Assembly Information This Melexis device is classified and qualified regarding soldering technology, solderability and moisture sensitivity level, as defined in this specification, according to following test methods: IPC/JEDEC J-STD-020 Moisture/Reflow Sensitivity Classification For Nonhermetic ...
Page 14
K-Bus Transceiver with integrated Voltage Regulator Disclaimer Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied description regarding the information set ...