HMP8112CN HARRIS [Harris Corporation], HMP8112CN Datasheet - Page 12

• Manufacturer Part Number: HMP8112CN
• Description: NTSC/PAL Video Decoder
• Manufacturer: HARRIS [Harris Corporation]

CLK frequency and Table 5 shows the number of data points
per video line to expect for a given standard. Data is output as
4:2:2 subsampled data in a Y-Cb/Y-Cr 16-bit sequence. The
Data Valid (DVLD) flag is asserted when video data is present
on the 16-bit output port of the HMP8112 (Y[7:0], CbCr[7:0]).
The ACTIVE flag is asserted when the active video portion of
the horizontal scan line is present on the data output port. See
Figure 15 for Synchronous Pixel Transfer Mode timing. DVLD is
asserted every time the output sample rate converter has a
valid output. When DVLD and ACTIVE are used together the
visual portion of the image can be captured. When DVLD is
used alone all valid data during the Horizontal, Vertical and Ref-
erence Burst Timing are available. ACTIVE is asserted from
lines 22 through 262.5 and lines 285.5 through 525 for NTSC
(and PAL M). Active is asserted from lines 23.5 through 310
and lines 336 through 623.5 for PAL (B, D, G, H, I, N, Comb N).
The CLK can be run on a 20MHz - 30MHz clock source. Data
will be output (on average) at the Output Data Rate shown in
Table 5 for a given standard. Data is clocked out synchronous
to CLK and will come in bursts. To smooth out the data rate to
a regular rate a CLK of 2X the average output data rate can
be used. In the 16-bit pixel transfer, data is sequenced on the
CbCr[7:0] data bus, starting with Cb and then Cr.
DATA WRITE
DATA READ
SDA
S
S
SCL
1000 100 (R/W)
1000 100 (R/W)
CHIP ADDR
CHIP ADDR
0x88
0x88
CONDITION
START
S
A
A
SUB ADDR
SUB ADDR
ADDRESS
FIGURE 14. REGISTER WRITE PROGRAMMING FLOW
1-7
A
A
FIGURE 13. I
REGISTER
SUBADDR
S
POINTED
TO BY
DATA
R/W
CHIP ADDR
8
0x89
HMP8112
2
A
C SERIAL TIMING FLOW
ACK
12
9
DATA
A
For Burst Mode output format the Y[7:0] output bus is used
to transfer all YCbCr data in 8-bit format. The data is also
4:2:2 subsampled but will only contain the active video por-
tion of the line. The HMP8112 uses an internal 32 deep fifo
to handle latencies between the output sample rate and the
CLK frequency. In this mode, the data is clocked out at the
CLK rate and only clock frequencies of 24.5454MHz, 27MHz
and 29.5MHz can be used. In 8-bit data mode, the data is
sequenced on the Y[7:0] bus in Cb, Y, Cr, Y format. ACTIVE
is asserted as soon as the mode is selected. DVLD when
asserted indicates a valid active pixel is available. Pixels dur-
ing the horizontal and vertical blanking are not available.
Only the active portions of the video line are output.
NTSC Square Pixel
NTSC CCIR 601
PAL B, D, G, H, I, N,
COMB N, CCIR601
PAL M CCIR 601
PAL B, D, G, H, I, N
Square Pixel
PAL M Square Pixel 14.74MHz
REGISTER
SUBADDR
POINTED
DATA
TO BY
STANDARD
A
1-7
P
TABLE 5. OUTPUT MODE STANDARDS
DATA
A
DATA
12.27MHz
14.74MHz
13.5MHz
13.5MHz
13.5MHz
OUTPUT
8
DATA
RATE
NA
ACK
PIXELS/
P
ACTIVE
9
LINE
640
720
720
720
768
640
S = START CYCLE
P = STOP CYCLE
A = ACKNOWLEDGE
NA = NO ACKNOWLEDGE
CONDITION
PIXELS/
FROM MASTER
FROM HMP8112
TOTAL
STOP
LINE
780
858
864
858
944
780
P
TOTAL
LINES/
FIELD
262.5
262.5
312.5
262.5
312.5
312.5