ADUC847BCP8-5 AD [Analog Devices], ADUC847BCP8-5 Datasheet - Page 62
ADUC847BCP8-5
Manufacturer Part Number
ADUC847BCP8-5
Description
MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
Manufacturer
AD [Analog Devices]
Datasheet
1.ADUC847BCP8-5.pdf
(108 pages)
- Current page: 62 of 108
- Download datasheet (2Mb)
ADuC845/ADuC847/ADuC848
I2CADD—I
Function:
SFR Address:
Power-On Default:
Bit Addressable:
I2CADD1—I
Function:
SFR Address:
Power-On Default:
Bit Addressable:
I2CDAT—I
Function:
SFR Address:
Power-On Default:
Bit Addressable:
The main features of the MicroConverter I
•
•
•
•
Only two bus lines are required: a serial data line (SDATA)
and a serial clock line (SCLOCK).
An I
devices. Because each slave device has a unique 7-bit
address, single master/slave relationships can exist at all
times even in a multislave environment.
The ability to respond to two separate addresses when
operating in slave mode.
On-chip filtering rejects <50 ns spikes on the SDATA and
the SCLOCK lines to preserve data integrity.
2
C master can communicate with multiple slave
2
2
C Data Register
C Address Register 1
2
C Address Register 2
MASTER
I
2
C
Figure 45. Typical I
Holds one of the I
uC001 at
9BH
55H
No
Same as the I2CADD.
F2H
7FH
No
The I2CDAT SFR is written to by user code to transmit data, or read by user code to read data just received by
the I
I2CCON SFR. User code should access I2CDAT only once per interrupt cycle.
9AH
00H
No
DV
2
DD
C interface. Accessing I2CDAT automatically clears any pending I
http://www.analog.com/microconverter
2
C System
SLAVE 1
SLAVE 2
I
I
2
2
C
C
2
2
C interface are
C peripheral addresses for the part. It may be overwritten by user code. Application Note
Rev. A | Page 62 of 108
Software Master Mode
The ADuC845/ADuC847/ADuC848 can be used as an I
master device by configuring the I
and writing software to output the data bit-by-bit. This is
referred to as a software master. Master mode is enabled by
setting the I2CM bit in the I2CCON register.
To transmit data on the SDATA line, MDE must be set to enable
the output driver on the SDATA pin. If MDE is set, the SDATA
pin is pulled high or low depending on whether the MDO bit is
set or cleared. MCO controls the SCLOCK pin and is always
configured as an output in master mode. In master mode, the
SCLOCK pin is pulled high or low depending on the whether
MCO is set or cleared.
To receive data, MDE must be cleared to disable the output
driver on SDATA. Software must provide the clocks by toggling
the MCO bit and reading the SDATA pin via the MDI bit. If
MDE is cleared, MDI can be used to read the SDATA pin. The
value of the SDATA pin is latched into MDI on a rising edge of
SCLOCK. MDI is set if the SDATA pin is high on the last rising
edge of SCLOCK. MDI is cleared if the SDATA pin is low on
the last rising edge of SCLOCK.
Software must control MDO, MCO, and MDE appropriately to
generate the start condition, slave address, acknowledge bits,
data bytes, and stop conditions. These functions are described
in Application Note uC001.
describes the format of the I
2
C interrupt and the I2CI bit in the
2
C standard 7-bit address.
2
C peripheral in master mode
2
C
Related parts for ADUC847BCP8-5
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DPG2 EVAL ADAPTER FOR XILINX BOARDS
Manufacturer:
Analog Devices Inc
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
Xilinx FMC Interface
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
RF Development Tools Sransceiver board for FMC evaluation kit
Manufacturer:
Analog Devices
Part Number:
Description:
Analog Devices: Data Converters: DAC 12-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Analog Devices: Data Converters: DAC 8-Bit, 10 ns to 100 ns Converters Selection Table
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
Low-Power Analog Front End with DSP Microcomputer
Manufacturer:
AD [Analog Devices]
Datasheet:
Part Number:
Description:
2 Pair/1 Pair ETSI Compatible HDSL Analog Front End
Manufacturer:
AD [Analog Devices]
Datasheet: