LT6210_12 LINER [Linear Technology], LT6210_12 Datasheet
LT6210_12
Related parts for LT6210_12
LT6210_12 Summary of contents
Page 1
FeaTures Programmable Supply Current and Bandwidth: n 10MHz at 300µA per Amplifier up to 200MHz at 6mA per Amplifier Rail-to-Rail Output: n 0.05V to 2.85V on 3V Single Supply High Slew Rate: 700V/µs n High Output Drive: n ±75mA Minimum ...
Page 2
LT6210/LT6211 absoluTe MaxiMuM raTings (Note 1) + – Total Supply Voltage ( ..............................13.2V Input Current (Note 8) .....................................±10mA Output Current .................................................±80mA Output Short-Circuit Duration (Note 2) ............ Indefinite Operating Temperature Range (Note 3).... –40°C to 85°C Specified ...
Page 3
T ground + 887Ω 150Ω; For 150Ω to 1.5V unless otherwise specified. ...
Page 4
LT6210/LT6211 elecTrical characTerisTics apply over the specified operating temperature range, otherwise specifications are at T ground + 887Ω 150Ω; For 150Ω to 1.5V unless otherwise ...
Page 5
T ground + 1.1k 150Ω; For 150Ω to 1.5V unless otherwise specified. ...
Page 6
LT6210/LT6211 elecTrical characTerisTics apply over the specified operating temperature range, otherwise specifications are at T ground + 11k 1k; For 1.5V unless otherwise specified. SYMBOL PARAMETER CONDITIONS ...
Page 7
Typical ac perForMance I (mA) per S V (V) Amplifier R (Ω SET ±5 6 20k 1 ±5 6 20k 2 ±5 6 20k –1 ±5 3 56k 1 ±5 3 56k 2 ±5 3 56k –1 ±5 ...
Page 8
LT6210/LT6211 Typical perForMance characTerisTics Input Noise Spectral Density (I = 6mA per Amplifier) S 100 V = ± 150 L – 25° 0.1 0.001 0.01 0.1 1 ...
Page 9
Typical perForMance characTerisTics Output Voltage Swing vs I LOAD –3 ± –3.2 CM ∆V = 50mV OS –3 25°C A –3.6 –3.8 –4.0 –4.2 –4 300µA –4 ...
Page 10
LT6210/LT6211 Typical perForMance characTerisTics 2nd and 3rd Harmonic Distortion vs Frequency (I = 6mA per Amplifier ±5V S – 887 OUT P-P – 150 L ...
Page 11
Typical perForMance characTerisTics –3dB Small-Signal Bandwidth vs Supply Current 1000 100mV OUT P 25°C A 100 V = ± ±1. 0.1 1 SUPPLY CURRENT PER AMPLIFIER ...
Page 12
LT6210/LT6211 applicaTions inForMaTion Setting the Quiescent Operating Current (I The quiescent bias point of the LT6210/LT6211 is SET with either an external resistor from the I lower potential or by drawing a current out of the I pin. However, the ...
Page 13
Capacitive Loads The LT6210/LT6211 are stable with any capacitive load. Although peaking and overshoot may result in the AC transient response, the amplifier’s compensation decreases bandwidth with increasing output capacitive load to ensure stability. To maintain a response ...
Page 14
LT6210/LT6211 Typical applicaTions 3V Cable Driver with Active Termination Driving back-terminated cables on single supplies usually results in very limited signal amplitude at the receiving end of the cable. However, positive feedback can be used to reduce the size of ...
Page 15
DescripTion 3.55 ±0.05 1.65 ±0.05 2.15 ±0.05 (2 SIDES) 0.25 ± 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS PIN 1 TOP MARK (SEE NOTE 6) 0.200 REF DD Package DD Package 10-Lead Plastic DFN (3mm × 3mm) 10-Lead Plastic ...
Page 16
LT6210/LT6211 package DescripTion 0.889 ± 0.127 (.035 ± .005) 5.23 3.20 – 3.45 (.206) (.126 – .136) MIN 0.305 ± 0.038 (.0120 ± .0015) TYP RECOMMENDED SOLDER PAD LAYOUT NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. ...
Page 17
Rev C) REV DATE DESCRIPTION C 3/11 Revised the tape and reel part numbers and temperature ranges in the Order Information section. Information furnished by Linear Technology Corporation is believed to be accurate and ...
Page 18
LT6210/LT6211 Typical applicaTion Line Driver with Power Saving Mode In applications where low distortion or high slew rate are desirable but not necessary at all times, it may be possible to decrease the LT6210 or LT6211’s quiescent current when the ...