BD6086GU_11 ROHM [Rohm], BD6086GU_11 Datasheet - Page 2

• Manufacturer Part Number: BD6086GU_11
• Description: 13LEDs ALC* Flash and Illumination
• Manufacturer: ROHM [Rohm]

●Absolute Maximum Ratings (Ta=25 ℃)
●Operating conditions(VBAT≧VIO, VBAT≧VGPIO, Ta=-25～85℃)
●Electrical Characteristics(Unless otherwise specified, Ta=25℃, VBAT=3.6V, VIO=VGPIO=1.8V)
© 2011 ROHM Co., Ltd. All rights reserved.
www.rohm.com
BD6086GU
【Circuit Current】
【LED Driver】
Maximum Applied voltage
Power Dissipation
Operating Temperature Range
Storage Temperature Range
Note1) Power dissipation deleting is 15.2mW/ ℃, when it’s used in over 25 ℃.
VBAT input voltage
VIO pin voltage
VGPIO pin voltage
VBAT Circuit current 1
VBAT Circuit current 2
VBAT Circuit current 3
VBAT Circuit current 4
VBAT Circuit current 5
VBAT Circuit current 6
VBAT Circuit current 7
VBAT Circuit current 8
LED current Step
(Current Setup)
LED current Step
(At slope)
LED Maximum setup current 1
LED Maximum setup current 2
LED current accurate 1
LED current accurate 2
LED current Matching
L Level output voltage
LED OFF Leak current
(It’s deleting is on the board that is ROHM’s standard)
Parameter
Parameter
Parameter
ILEDSTPW1
ILEDSTPRGB1
ILEDSTPW2
ILEDSTPRGB2
ILEDMT
Symbol
Symbol
Symbol
VGPIO
IMAX1
IMAX2
VMAX
ILED1
ILED2
IBAT1
IBAT2
IBAT3
IBAT4
IBAT5
IBAT6
IBAT7
IBAT8
VBAT
VOL2
Topr
ILKL
Tstg
VIO
Pd
Min.
18
18
-
-
-
-
-
-
-
-
-
-
-
-
-
-55 ～ +150
1900 Note1)
1.65 ～ 3.3
1.65 ～ 3.3
-25 ～ +85
2.7 ～ 5.5
2/80
Limits
Limits
Limits
0.35
Typ.
128
128
256
128
123
110
0.1
0.5
7.5
61
92
20
20
7
5
-
-
-
-
30.48
Max.
25.6
11.3
165
102
140
3.0
3.0
1.0
0.2
1.0
65
22
22
10
Unit
mW
Unit
step
step
Unit
mA
mA
mA
mA
mA
mA
mA
mA
μA
μA
μA
μA
μA
℃
℃
%
V
V
V
V
V
RESETB=0V, VIO=VGPIO=0V
RESETB=0V, VIO=1.8V, VGPIO=0V
REG1,REG2 Low consumption mode
Io=0mA,VIO=1.8V, VGPIO=0V
(control is rejistor setup)
REG1,REG2 Nomal mode Io=0mA
(control is rejistor setup)
DC/DC x1mode, Io=60mA
VBAT=4.0V
DC/DC x1.5mode, Io=60mA
VBAT=3.6V
DC/DC x2mode, Io=60mA
VBAT=2.7V
ALC operating ,
Setup of ALCEN=1, AD cycle =0.5s
Sensor current removes
WLED1~7
RGB1 group, RGB2 group
WLED1~7
RGB1 group, RGB2 group
WLED1~7, LED terminal voltage
=1V
RGB1 group, RGB2 group,
LED terminal voltage =1V
RGBISET=100kΩ
WLED1~7, ILED=20mA setup,
LED terminal voltage =1V
RGB1 group, RGB2 group
ILED=20mA, RGBISET =120kΩ
LED terminal voltage =1V
WLED1~7,
RGB1 group, RGB2 group
RGB2 group GPO setup,
IOL=1mA
Condition
Technical Note
2011.04 - Rev.A