HIP6301CBZA-T INTERSIL [Intersil Corporation], HIP6301CBZA-T Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
HIP6301CBZA-T
Manufacturer Part Number
HIP6301CBZA-T
Description
Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
Manufacturer
INTERSIL [Intersil Corporation]
Datasheet
1.HIP6301CBZA-T.pdf
(17 pages)
For the first 32 PWM switching cycles, the DAC output
remains inhibited and the PWM outputs remain three stated.
From the 33rd cycle and for another, approximately 150
cycles the PWM output remains low, clamping the lower
output MOSFETs to ground, see Figure 3. The time
variability is due to the Error Amplifier, Sawtooth Generator
and Comparators moving into their active regions. After this
short interval, the PWM outputs are enabled and increment
the PWM pulse width from zero duty cycle to operational
pulse width, thus allowing the output voltage to slowly reach
the CORE voltage. The CORE voltage will reach its
programmed value before the 2048 cycles, but the PGOOD
output will not be initiated until the 2048th PWM switching
cycle.
The Soft-Start time or delay time, DT = 2048/F
oscillator frequency, F
160µs, the PWM outputs are held in a three state level as
explained above. After this period and a short interval
described above, the PWM outputs are initiated and the
voltage rises in 10.08ms, for a total delay time DT of
10.24ms.
Figure 3 shows the start-up sequence as initiated by a fast
rising 5V supply, V
short rise to the three state level in PWM 1 output during first
32 PWM cycles.
Figure 4 shows the waveforms when the regulator is
operating at 200kHz. Note that the Soft-Start duration is a
function of the Channel Frequency as explained previously.
Also note the pulses on the COMP terminal. These pulses
are the current correction signal feeding into the comparator
input (see the Block Diagram on page 2).
Figure 5 shows the regulator operating from an ATX supply.
In this figure, note the slight rise in PGOOD as the 5V supply
rises. The PGOOD output stage is an open drain NMOS
transistor. On rising V
PGOOD output slightly positive before the NMOS transistor
pulls “down”, generating the slight rise in PGOOD output
voltage.
Note that Figure 5 shows the 12V gate driver voltage
available before the 5V supply to the HIP6301 has reached
its threshold level. If conditions were reversed and the 5V
supply was to rise first, the start-up sequence would be
different. In this case the HIP6303 will sense an overcurrent
condition due to charging the output capacitors. The supply
will then restart and go through the normal Soft-Start cycle.
CC,
CC
SW
applied to the HIP6301. Note the
, the pull-up resistor begins to move
, of 200kHz, the first 32 cycles or
9
SW
. For an
HIP6301
HIP6301
FIGURE 3. START-UP OF 4 PHASE SYSTEM OPERATING AT
FIGURE 4. START-UP OF 4 PHASE SYSTEM OPERATING AT
FIGURE 5. SUPPLY POWERED BY ATX SUPPLY
ATX SUPPLY ACTIVATED BY ATX “PS-ON PIN”
DELAY TIME
500kHz
200kHz
V
DELAY TIME
IN
= 5V, CORE LOAD CURRENT = 31A
FREQUENCY 200kHz
V
IN
V
IN
= 12V
= 12V
December 27, 2004
12V ATX
SUPPLY
PGOOD
V
5 V ATX
SUPPLY
PWM 1
OUTPUT
PGOOD
V
5V
V
V COMP
PGOOD
V
5V
V
FN4765.6
CORE
CORE
CC
CORE
CC