MN101C62D PANASONIC [Panasonic Semiconductor], MN101C62D Datasheet - Page 2

• Manufacturer Part Number: MN101C62D
• Description: The lower limit for operation guarantee for flash memory built-in type is 2.5 V
• Manufacturer: PANASONIC [Panasonic Semiconductor]

MAD00020EEM
Operating supply current
Supply current at HALT
Supply current at STOP
Timer Counter
(Continue)
Serial Interface
I/O Pins
A/D Inputs
Special Ports
Electrical Characteristics
Supply current
Parameter
I/O
Symbol
Timer counter 7 : 16-bit × 1
Watchdog timer
Timer counter 8 : 16-bit × 1
Serial 0 : synchronous type/UART (full-duplex) × 1
Serial 1 : synchronous type/UART (full-duplex) × 1
Serial 2 : synchronous type / single-master I
Buzzer output, remote control carrier signal output, high-current drive port
68
IDD1
IDD2
IDD3
IDD4
IDD5
IDD6
10-bit × 8-ch. (with S/H)
(square-wave output, 16-bit PWM output (cycle / duty continuous variable), event count, synchronous output
(square-wave output, 16-bit PWM output (cycle / duty continuous variable), event count, synchronous output
evevt, pulse width measurement, input capture, generation of real time)
evevt, pulse width measurement, input capture, generation of real time)
• Common use • Specified pull-up resistor available • Input/output selectable (bit unit)
Clock source ····················· 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC
Interrupt source ················ coincidence with compare register 7 (2 lines)
Interrupt source ················ 1/65536, 1/262144, 1/1048576 of system clock frequency
Clock source ····················· 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC
Interrupt source ················ coincidence with compare register 7 (2 lines)
Watchdog timer
Interrupt source ················ 1/65536, 1/262144, 1/1048576 of system clock frequency
Clock source ····················· 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2;
Clock source ····················· 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3;
Clock source ····················· 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3;
fx = 32 kHz, VDD = 3 V, Ta = 25°C
fx = 32 kHz, VDD = 3 V, Ta = 85°C
fosc = 20 MHz, VDD = 5 V
fx = 32 kHz, VDD = 3 V
VDD = 5 V, Ta = 25°C
VDD = 5 V, Ta = 85°C
oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency
oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency
1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency
1/2, 1/4, 1/8, 1/32 of OSC oscillation clock frequency
1/2,1/8 of timer counter 2 output;
1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency
Condition
2
C
See the next page for pin assignment and support tool.
MN101C62D, MN101C62F
min
Limit
typ
18
30
6
max
30
60
30
50
8
2
Unit
mA
µA
µA
µA
µA
µA
2