NS16C2552TVA NSC [National Semiconductor], NS16C2552TVA Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
NS16C2552TVA
Manufacturer Part Number
NS16C2552TVA
Description
Dual UART with 16-byte/64-byte FIFOs and up to 5 Mbit/s Data Rate
Manufacturer
NSC [National Semiconductor]
Datasheet
1.NS16C2552TVA.pdf
(43 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NS16C2552TVA/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
NS16C2552TVAX/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
DSR1
DSR2
DCD1
DCD2
RI1
RI2
MF1
MF2
5.0 Pin Descriptions
Signal
Name
Type
O
I
I
I
PLCC
Pin #
41
29
42
30
43
31
35
19
TQFP
Pin #
39
25
40
26
41
27
32
14
(Continued)
UART Data-set-ready:
When low, DSR indicates that the remote link partner is ready to establish the
communications link. The DSR signal is a MODEM status input and can be read for
the appropriate channel in MSR[5]. This bit reflects the complement of the DSR
signal. MSR[1] indicates whether the DSR input has changed state since the previous
read of the MODEM Status Register.
Note: Whenever the DSR bit of the MSR changes state, an interrupt is generated if the MODEM Status
UART Data-carrier-detect:
When low, DCD indicates that the data carrier has been detected by the remote link
partner. The DCD signal is a MODEM status input and can be read for the appropriate
channel in MSR[7]. This bit reflects the complement of the DCD signal. MSR[3]
indicates if the DCD input has changed state since the previous reading of the
MODEM Status Register. DCD has no effect on the receiver.
Note: Whenever the DCD bit of the MSR changes state, an interrupt is generated if the MODEM Status
UART Ring-detector:
When low, RI indicates that a telephone ringing is active. The RI signal is a MODEM
status input and can be read for the appropriate channel in MSR[6]. This bit reflects
the complement of the RI signal. MSR[2] indicates whether the RI input signal has
changed state from low to high since the previous reading of the MSR.
Note: Whenever the RI bit of the MSR changes from a high to a low state, an interrupt is generated if the
UART Multi-function Pin:
MF can be programmed for any one of three signal functions OUT2, BAUDOUT or
RXRDY. Bits 2 and 1 of the Alternate Function Register select which output signal will
be present on this pin. OUT2 is the default signal and it is selected immediately after
master reset or power-up.
The OUT2 can be set active low by programming bit 3 (OUT2) of the MCR to a logic
1. A Master Reset operation sets this signal to its inactive (high) state. Loop Mode
holds this signal in its inactive state.
The BAUDOUT signal is the 16X clock output that drives the transmitter and receiver
logic of the associated serial channel. This signal is the result of the XIN clock divided
by the value in the Divisor Latch Registers. The BAUDOUT signal for each channel is
internally connected to provide the receiver clock (formerly RCLK on the PC16550D).
The RXRDY signal can be used to request a DMA transfer of data from the RCVR
FIFO. Details regarding the active and inactive states of this signal are described in
Section 6.5 FIFO CONTROL REGISTER (FCR) and Section 7.9 DMA OPERATION.
Interrupt is enabled.
Interrupt is enabled.
MODEM Status Interrupt is enabled.
7
Description
www.national.com