XC68HC705JB3 Motorola, XC68HC705JB3 Datasheet - Page 18
XC68HC705JB3
Manufacturer Part Number
XC68HC705JB3
Description
MICROCONTROLLER
Manufacturer
Motorola
Datasheet
1.XC68HC705JB3.pdf
(134 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XC68HC705JB3JP
Manufacturer:
MOT
Quantity:
6 223
- Current page: 18 of 134
- Download datasheet (2Mb)
GENERAL RELEASE SPECIFICATION
1.4.3 RESET
1.4.4 IRQ
1.4.5 3.3V
1.4.6 D+ and D–
1.4.7 PA0-PA7
MOTOROLA
1-6
External Clock
An external clock from another CMOS-compatible device can be connected to the
OSC1 input, with the OSC2 input not connected, as shown in Figure 1-3 (b).This
configuration is possible ONLY when the crystal/ceramic resonator mask option is
selected.
This is an I/O pin. This pin can be used as an input to reset the MCU to a known
start-up state by pulling it to the low state. The RESET pin contains a steering
diode to discharge any voltage on the pin to V
internal pull-up is also connected between this pin and V
tains an internal Schmitt trigger to improve its noise immunity as an input. This pin
is an output pin if LVR triggers an internal reset.
This input pin drives the asynchronous IRQ interrupt function of the CPU. The IRQ
interrupt function has a mask option to provide either only negative edge-sensitive
triggering or both negative edge-sensitive and low level-sensitive triggering. If the
option is selected to include level-sensitive triggering, the IRQ input requires an
external resistor to V
an internal Schmitt trigger as part of its input to improve noise immunity.
Each of the PA0 to PA3 I/O pins may be connected as an OR function with the IRQ
interrupt function by a mask option. This capability allows keyboard scan
applications where the transitions or levels on the I/O pins will behave the same
as the IRQ pin. The edge or level sensitivity selected by a separate mask option
for the IRQ pin also applies to the I/O pins OR’ed to create the IRQ signal.
This is an output reference voltage nominally set at 3.3V dc.
These two lines carry the USB differential data. For low speed device such as
MC68HC05JB3, a 1.5 k resistor is required to be connected across D– and 3.3V
for proper signal termination.
These eight I/O lines comprise Port A. PA0 to PA7 are push-pull pins with pull-
down devices. The state of any pin is software programmable and all Port A lines
are configured as inputs during power-on or reset.
DD
for "wired-OR" operation, if desired. The IRQ pin contains
GENERAL DESCRIPTION
November 5, 1998
NOTE
DD
, when the power is removed. An
DD
. The RESET pin con-
MC68HC05JB3
REV 1
Related parts for XC68HC705JB3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
3N2046367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MOTOROLA POWERPC 603e MICROPROCESSOR
Manufacturer:
Motorola
Part Number:
Description:
Motorola Semiconductor Datasheet Library
Manufacturer:
Motorola
Part Number:
Description:
SWITCHMODE Schottky Power Rectifier(POWERTAP III Package)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SWITCHMODE Schottky Power Rectifirer
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Search -----> MTE53N50E
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SCHOTTKY BARRIER RECTIFIER 200 AMPERES 60 VOLT
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
NPN SILICON POWER DARLINGTON TRANSISTOR
Manufacturer:
Motorola
Datasheet: