HIP4080 Intersil Corporation, HIP4080 Datasheet - Page 6

• Manufacturer Part Number: HIP4080
• Description: 80V/2.5A Peak/ High Frequency Full Bridge FET Driver
• Manufacturer: Intersil Corporation

Pin Descriptions
NUMBER
PIN
18
10
11
12
13
14
15
16
17
19
20
1
2
3
4
5
6
7
8
9
SYMBOL
HDEL
LDEL
AHO
BHO
BHB
HEN
OUT
AHB
AHS
ALO
V
V
BLO
BHS
V
ALS
BLS
DIS
IN+
IN-
CC
DD
SS
B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of boot-
strap diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30 A out of this
pin to maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.
High-side Enable input. Logic level input that when low overrides IN+/IN- (Pins 6 and 7) to put AHO and BHO
drivers (Pins 11 and 20) in low output state. When HEN is high AHO and BHO are controlled by IN+/IN- inputs.
The pin can be driven by signal levels of 0V to 15V (no greater than V
hold HEN high, so no connection is required if high-side and low-side outputs are to be controlled by IN+/IN-
inputs.
DISable input. Logic level input that when taken high sets all four outputs low. DIS high overrides all other inputs.
When DIS is taken low the outputs are controlled by the other inputs. The pin can be driven by signal levels of
0V to 15V (no greater than V
Chip negative supply, generally will be ground.
OUTput of the input control comparator. This output can be used for feedback and hysteresis.
Non-inverting input of control comparator. If IN+ is greater than IN- (Pin 7) then ALO and BHO are low level
outputs and BLO and AHO are high level outputs. If IN+ is less than IN- then ALO and BHO are high level out-
puts and BLO and AHO are low level outputs. DIS (Pin 3) high level will override IN+/IN- control for all outputs.
HEN (Pin 2) low level will override IN+/IN- control of AHO and BHO. When switching in four quadrant mode,
dead time in a half bridge leg is controlled by HDEL and LDEL (Pins 8 and 9).
Inverting input of control comparator. See IN+ (Pin 6) description.
High-side turn-on DELay. Connect resistor from this pin to V
of both high-side drivers. The low-side drivers turn-off with no adjustable delay, so the HDEL resistor guarantees
no shoot-through by delaying the turn-on of the high-side drivers. HDEL reference voltage is approximately 5.1V.
Low-side turn-on DELay. Connect resistor from this pin to V
of both low-side drivers. The high-side drivers turn-off with no adjustable delay, so the LDEL resistor guarantees
no shoot-through by delaying the turn-on of the low-side drivers. LDEL reference voltage is approximately 5.1V.
A High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of boot-
strap diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30 A out of this
pin to maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.
A High-side Output. Connect to gate of A High-side power MOSFET.
A High-side Source connection. Connect to source of A High-side power MOSFET. Connect negative side of
bootstrap capacitor to this pin.
A Low-side Output. Connect to gate of A Low-side power MOSFET.
A Low-side Source connection. Connect to source of A Low-side power MOSFET.
Positive supply to gate drivers. Must be same potential as V
diodes.
Positive supply to lower gate drivers. Must be same potential as V
B Low-side Source connection. Connect to source of B Low-side power MOSFET.
B Low-side Output. Connect to gate of B Low-side power MOSFET.
B High-side Source connection. Connect to source of B High-side power MOSFET. Connect negative side of
bootstrap capacitor to this pin.
B High-side Output. Connect to gate of B High-side power MOSFET.
DD
). An internal 100 A pull-up to V
HIP4080
6
DESCRIPTION
SS
SS
DD
to set timing current that defines the turn-on delay
to set timing current that defines the turn-on delay
DD
(Pin 16). Connect to anodes of two bootstrap
CC
will hold DIS high if this pin is not driven.
(Pin 15). De-couple this pin to V
DD
). An internal 100 A pull-up to V
SS
(Pin 4).
DD
will