M30620FCAFP Mitsubishi, M30620FCAFP Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/4/451/mitsubishi_sml.jpg)
M30620FCAFP
Manufacturer Part Number
M30620FCAFP
Description
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Manufacturer
Mitsubishi
Datasheet
1.M30620FCAFP.pdf
(274 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M30620FCAFP
Manufacturer:
QFP
Quantity:
513
Part Number:
M30620FCAFP
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
M30620FCAFP#D3
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
M30620FCAFP#D5
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
M30620FCAFP#U3
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30620FCAFP#U3
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
M30620FCAFP#U5
Manufacturer:
DIBCOM
Quantity:
2
Company:
Part Number:
M30620FCAFP#U5
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30620FCAFP#U5
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Software Reset
Software Reset
Software Reset
Processor Mode
Writing “1” to bit 3 of the processor mode register 0 (address 0004
microcomputer. A software reset has the same effect as a hardware reset. The contents of internal RAM
are preserved.
(1) Types of Processor Mode
(2) Setting Processor Modes
One of three processor modes can be selected: single-chip mode, memory expansion mode, and micro-
processor mode. The functions of some pins, the memory map, and the access space differ according to
the selected processor mode.
The processor mode is set using the CNV
0004
Regardless of the level of the CNV
never change the processor mode bits when changing the contents of other bits. Also do not attempt to
shift to or from the microprocessor mode within the program stored in the internal ROM area.
Figure 1.7.1 shows the processor mode register 0 and 1.
Figure 1.7.2 shows the memory maps applicable for each of the modes.
• Single-chip mode
• Memory expansion mode
• Microprocessor mode
• Applying V
• Applying V
In single-chip mode, only internal memory space (SFR, internal RAM, and internal ROM) can be
accessed. However, after the reset has been released and the operation of shifting from the micropro-
cessor mode has started (“H” applied to the CNV
even if the CPU shifts to the single-chip mode.
Ports P0 to P10 can be used as programmable I/O ports or as I/O ports for the internal peripheral
functions.
In memory expansion mode, external memory can be accessed in addition to the internal memory
space (SFR, internal RAM, and internal ROM). However, after the reset has been released and the
operation of shifting from the microprocessor mode has started (“H” applied to the CNV
internal ROM area cannot be accessed even if the CPU shifts to the memory expansion mode.
In this mode, some of the pins function as the address bus, the data bus, and as control signals. The
number of pins assigned to these functions depends on the bus and register settings. (See “Bus
Settings” for details.)
In microprocessor mode, the SFR, internal RAM, and external memory space can be accessed. The
internal ROM area cannot be accessed.
In this mode, some of the pins function as the address bus, the data bus, and as control signals. The
number of pins assigned to these functions depends on the bus and register settings. (See “Bus
Settings” for details.)
The microcomputer begins operation in single-chip mode after being reset. Memory expansion mode
is selected by writing “01
The microcomputer starts to operate in microprocessor mode after being reset.
16
). Do not set the processor mode bits to “10
SS
CC
to CNV
to CNV
SS
SS
2
pin
pin
” to the processor mode is selected bits.
SS
pin, changing the processor mode bits selects the mode. Therefore,
SS
pin and the processor mode bits (bits 1 and 0 at address
2
”.
SS
pin), the internal ROM area cannot be accessed
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
16
) applies a (software) reset to the
M16C / 62A Group
Mitsubishi microcomputers
SS
pin), the
21