M30620FCAFP Mitsubishi, M30620FCAFP Datasheet - Page 62
![no-image](/images/manufacturer_photos/0/4/451/mitsubishi_sml.jpg)
M30620FCAFP
Manufacturer Part Number
M30620FCAFP
Description
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Manufacturer
Mitsubishi
Datasheet
1.M30620FCAFP.pdf
(274 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M30620FCAFP
Manufacturer:
QFP
Quantity:
513
Part Number:
M30620FCAFP
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
M30620FCAFP#D3
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
M30620FCAFP#D5
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
M30620FCAFP#U3
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30620FCAFP#U3
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Company:
Part Number:
M30620FCAFP#U5
Manufacturer:
DIBCOM
Quantity:
2
Company:
Part Number:
M30620FCAFP#U5
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Part Number:
M30620FCAFP#U5
Manufacturer:
RENESAS/瑞萨
Quantity:
20 000
Precautions for Interrupts
62
Precautions for Interrupts
(1) Reading address 00000
(2) Setting the stack pointer
(3) The NMI interrupt
(4) External interrupt
• When maskable interrupt is occurred, CPU read the interrupt information (the interrupt number and
• The value of the stack pointer immediately after reset is initialized to 0000
•The NMI interrupt can not be disabled. Be sure to connect NMI pin to Vcc via a pull-up resistor if
• The NMI pin also serves as P8
• Do not reset the CPU with the input to the NMI pin being in the “L” state.
• Do not attempt to go into stop mode with the input to the NMI pin being in the “L” state. With the input to
• Do not attempt to go into wait mode with the input to the NMI pin being in the “L” state. With the input to
• Signals input to the NMI pin require an “L” level of 1 clock or more, from the operation clock of the CPU.
• Either an “L” level or an “H” level of at least 250 ns width is necessary for the signal input to pins INT
• When the polarity of the INT
interrupt request level) in the interrupt sequence.
The interrupt request bit of the certain interrupt written in address 00000
Reading address 00000
Though the interrupt is generated, the interrupt routine may not be executed.
Do not read address 00000
before setting a value in the stack pointer may become a factor of runaway. Be sure to set a value in
the stack pointer before accepting an interrupt. When using the NMI interrupt, initialize the stack point
at the beginning of a program. Concerning the first instruction immediately after reset, generating any
interrupts including the NMI interrupt is prohibited.
unused.
allows reading the pin value. Use the reading of this pin only for establishing the pin level at the time
when the NMI interrupt is input.
the NMI being in the “L” state, the CM10 is fixed to “0”, so attempting to go into stop mode is turned
down.
the NMI pin being in the “L” state, the CPU stops but the oscillation does not stop, so no power is saved.
In this instance, the CPU is returned to the normal state by a later interrupt.
through INT
After changing the polarity, set the interrupt request bit to “0”. Figure 1.11.13 shows the procedure for
changing the INT interrupt generate factor.
_______
_______
_______
_______
_______
________
_______
5
______
regardless of the CPU operation clock.
_______
_______
16
________
by software sets enabled highest priority interrupt source request bit to “0”.
16
0
to INT
by software.
16
5
________
, which is exclusively input. Reading the contents of the P8 register
5
pins is changed, the interrupt request bit is sometimes set to “1”.
_______
_______
_______
_______
_______
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
16
will then be set to “0”.
16
. Accepting an interrupt
M16C / 62A Group
Mitsubishi microcomputers
________
0