D38999/49 Defense Supply Center, D38999/49 Datasheet - Page 32
D38999/49
Manufacturer Part Number
D38999/49
Description
D38999K / D38999J 500 Cycle Contact
Manufacturer
Defense Supply Center
Datasheet
1.D3899949.pdf
(111 pages)
- Current page: 32 of 111
- Download datasheet (686Kb)
the qualifying activity the capability of manufacturing products which meet the performance requirements of
this specification. Refer to the qualifying activity for the guidelines necessary to retain qualification to this
particular specification. The contractor shall immediately notify the qualifying activity at any time that the
inspection data indicates failure of the qualified product to meet the performance requirements of this
specification.
B inspections. The documentation requirements of the applicable military or industry test procedures do not
apply.
examined for completeness, workmanship, and identification requirements. Attention shall be given to
those assemblies that require a gasket to determine the condition of the gasket. Gaskets missing, twisted,
buckled, kinked, or damaged in any way shall be cause for rejection. Each connector (except hermetics)
shall be visually inspected for the presence of filler compound in the cavity between wire termination end of
insert and shell.
the pertinent military standard are considered critical.
4.3.3.1 Failures. One or more failures shall be cause for refusal to grant qualification.
4.3.4 Retention of qualification. To retain qualification, the contractor shall verify in coordination with
4.4 Conformance inspection.
4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and
4.4.1.1 Group A inspection. Group A inspection shall consist of the inspections specified in table XIII.
4.4.1.1.1 Visual examination (group A inspection). Each connector and accessory shall be visually
4.4.1.1.2 Critical examinations (group A inspection). The following dimensions and features shown on
a. Mating diameters H and W for series I, II, and III; LL, L and MM for series IV of figures 1, 2, 3, and
b. Key or keyway positions.
c. Contact pattern relative to datum features (hermetics only).
d. Registration of grommet and insert markings. (Hole pattern between the grommet and the front
1/ Contacts shipped with connectors other than hermetics shall be from lots that have met
2/ 100-percent inspection.
3/ The contractor may use in-process controls for this requirement.
4/ Test between two adjacent contacts and between two peripheral contacts and the shell.
Inspection
Visual inspection 2/ --------------------------------------------------
Critical examination 2/ 3/ -------------------------------------------
Insulation resistance at ambient temperature 2/ 3/ 4/ ----
Dielectric withstanding voltage at sea level 2/ 3/ 4/ --------
Air leakage (hermetics only) 2/ 3/ -------------------------------
7 (maximum on plugs, minimum on receptacles).
face of the insert.)
the requirements of MIL-C-39029.
TABLE XIII. Group A inspection. 1/
MIL-DTL-38999K
32
3.1, 3.3, 3.4, 3.5,
3.43, and 3.4
Requirement
paragraph
3.13.1
3.14
3.1
3.9
paragraph
4.4.1.1.1
4.4.1.1.2
4.5.10.1
4.5.9.1
4.5.5
Test
Related parts for D38999/49
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Military Spec Transistors, PNP Germanium, High Power
Manufacturer:
Defense Supply Center Columbus
Part Number:
Description:
Radiation hardened D.I., high speed, low power, current feedback amplifier with programmable output limiting
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
Radiation hardened D.I., ultra high speed current feedback amplifier with offset adjust
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
Radiation hardened D.I., low power, current feedback video operational amplifier with output disable
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
Radiation hardened D.I., dual, high speed, low power, video closed loop buffer
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
Microcircuits, Digital, CMOS Dual, Retriggerable/Resettable Monostable Multivibrator, Monolithic Silicon
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
7.5V, 10Wt General purpose voltage reference/regulator diode
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
6.8V, 400mWt General purpose voltage reference/regulator diode
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
300mA Iout, 100V Vrrm Fast Recovery Rectifier
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
500mA Iout, 50V Vrrm Fast Recovery Rectifier
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
150mA Iout, 75V Vrrm Fast Recovery Rectifier
Manufacturer:
Defense Electronics Supply Center
Part Number:
Description:
1.0A Iout, 200V Vrrm General Purpose Silicon Rectifier
Manufacturer:
Defense Electronics Supply Center