AM79C970A Advanced Micro Devices, AM79C970A Datasheet - Page 32
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
AM79C970A
Manufacturer Part Number
AM79C970A
Description
PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C970A.pdf
(219 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM79C970ACK
Manufacturer:
AMD
Quantity:
271
Company:
Part Number:
AM79C970AKC
Manufacturer:
AMtek
Quantity:
11
Part Number:
AM79C970AKC
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
226
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKCW
Manufacturer:
AMD
Quantity:
6 557
Part Number:
AM79C970AVC
Manufacturer:
AMD
Quantity:
20 000
Slave I/O Transfers
After the PCnet-PCI II controller is configured as an I/O
device by setting IOEN (for regular I/O mode) or
MEMEN (for memory mapped I/O mode) in the PCI
Command register, it starts monitoring the PCI bus for
access to its CSR, BCR or EEPROM locations. If config-
ured for regular I/O mode, the PCnet-PCI II controller
will look for an address that falls within its 32 bytes of I/O
address space (starting from the I/O base address). The
PCnet-PCI II controller asserts DEVSEL if it detects an
address match and the access is an I/O cycle. If config-
ured for memory mapped I/O mode, the PCnet-PCI II
controller will look for an address that falls within its 32
bytes of memory address space (starting from the mem-
ory mapped I/O base address). The PCnet-PCI II con-
troller asserts DEVSEL if it detects an address match
and the access is a memory cycle. DEVSEL is asserted
two clock cycles after the host has asserted FRAME.
The PCnet-PCI II controller will not assert DEVSEL if it
detects an address match, but the PCI command is not
of the correct type. In memory mapped I/O mode, the
PCnet-PCI II controller aliases all accesses to the I/O re-
sources of the command types “Memory Read Multiple”
32
AMD
DEVSEL
FRAME
IDSEL
TRDY
STOP
IRDY
C/BE
PAR
CLK
AD
1
Figure 2. Slave Configuration Write
ADDR
1011
2
P R E L I M I N A R Y
Am79C970A
PAR
3
and “Memory Read Line” to the basic Memory Read
command. All accesses of the type “Memory Write and
Invalidate” are aliased to the basic Memory Write com-
mand. 8-bit, 16-bit and 32-bit non-burst transactions are
supported. The PCnet-PCI II controller decodes only the
upper 30 address lines to determine which I/O resource
is accessed.
The typical number of wait states added to a slave I/O or
memory mapped I/O read or write access on the part of
the PCnet-PCI II controller is 6 to 7 clock cycles,
depending upon the relative phases of the internal
Buffer Management Unit clock and the CLK signal,
since the internal Buffer Management Unit clock is a
divide-by-two version of the CLK signal.
The PCnet-PCI II controller does not support burst
transfers for access to its I/O resources. When the host
keeps FRAME asserted for a second data phase,
the PCnet-PCI II controller will disconnect the transfer.
The PCnet-PCI II controller supports fast back-to-back
transactions to different targets. This is indicated by the
Fast Back-To-Back Capable bit (PCI Status register,
4
DATA
BE
5
PAR
6
7
19436A-5