AM79C970A Advanced Micro Devices, AM79C970A Datasheet - Page 97
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
AM79C970A
Manufacturer Part Number
AM79C970A
Description
PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C970A.pdf
(219 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM79C970ACK
Manufacturer:
AMD
Quantity:
271
Company:
Part Number:
AM79C970AKC
Manufacturer:
AMtek
Quantity:
11
Part Number:
AM79C970AKC
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
226
Part Number:
AM79C970AKC/W
Manufacturer:
AMD
Quantity:
20 000
Company:
Part Number:
AM79C970AKCW
Manufacturer:
AMD
Quantity:
6 557
Part Number:
AM79C970AVC
Manufacturer:
AMD
Quantity:
20 000
Power Savings Modes
The PCnet-PCI II controller supports two hardware
power savings modes. Both are entered by driving the
SLEEP pin LOW.
The power down mode that yields the most power sav-
ings is called coma mode. In coma mode, the entire
device is shut down. All inputs are ignored except the
SLEEP pin itself. Coma mode is enabled when AWAKE
(BCR2, bit 2) is at its default value of ZERO and SLEEP
is asserted.
The second power saving mode is called snooze mode.
In snooze mode, enabled by setting AWAKE to ONE
and driving the SLEEP pin LOW, the T-MAU receive cir-
cuitry will remain active even while the SLEEP pin is
driven LOW. The LNKST output is the only one of the
LED pins that continues to function. All other sections of
the device are shut down. The LNKSTE bit must be set
in BCR4 to enable indication of a good 10BASE-T link if
there are link beat pulses or valid frames present. This
LNKST pin can be used to drive an LED and/or external
hardware that directly controls the SLEEP pin of the
PCnet-PCI II controller. This configuration effectively
wakes the system when there is any activity on the
10BASE-T link. Snooze mode can be used only if the
T-MAU is the selected network port. Link beat pulses
are not transmitted during snooze mode.
The SLEEP pin must not be asserted while the PCnet-
PCI II controller is requesting the bus or while a slave or
bus master cycle is in progress. A recommended
method is to set the PCnet-PCI II controller into
suspend mode by setting the SPND bit in CSR5 to ONE
prior to asserting the SLEEP pin. Another recom-
mended method is to stop the device by setting the
STOP bit in CSR0 to ONE prior to asserting the
SLEEP pin.
Before the sleep mode is invoked, the PCnet-PCI II
controller will perform an internal S_RESET. This
S_RESET operation will not affect the values of the BCR
registers or the PCI configuration space. S_RESET ter-
minates all network activity abruptly. The host can use
the suspend mode (SPND, CSR5, bit 0) to terminate all
network activity in an orderly sequence before issuing
an S_RESET.
When coming out of the sleep mode, the PCnet-PCI II
controller can be programmed to generate an interrupt
and inform the driver about the wake-up. The
PCnet-PCI II controller will set SLPINT (CSR5, bit 9),
P R E L I M I N A R Y
Am79C970A
when coming out of the sleep mode. INTA will be
asserted, when the enable bit SLPINTE (CSR5, bit 8) is
set to ONE. Note that the assertion of INTA due to
SLPINT is not dependent on the main interrupt enable
bit INEA (CSR0, bit 6), which will be cleared by the reset
going into the sleep mode.
The SLEEP pin should not be asserted during power
supply ramp-up. If it is desired that SLEEP be asserted
at power up time, then the system must delay the asser-
tion of SLEEP until three clock cycles after the comple-
tion of a hardware reset operation.
IEEE 1149.1 Test Access Port Interface
An IEEE 1149.1 compatible boundary scan Test Access
Port is provided for board level continuity test and diag-
nostics. All digital input, output and input/output pins are
tested. Analog pins, including the AUI differential driver
(DO ) and receivers (DI , CI ), and the crystal input
(XTAL1/XTAL2) pins, are not tested. The T-MAU drivers
TXD , TXP and receiver RXD are also not tested.
The following is a brief summary of the IEEE 1149.1
compatible
PCnet-PCI II controller.
Boundary Scan Circuit
The boundary scan test circuit requires four pins (TCK,
TMS, TDI and TDO), defined as the Test Access Port
(TAP). It includes a finite state machine (FSM), an in-
struction register, a data register array, and a power-on
reset circuit. Internal pull-up resistors are provided for
the TDI, TCK, and TMS pins. The boundary scan circuit
remains active during Sleep mode.
TAP Finite State Machine
The TAP engine is a 16-state finite state machine
(FSM), driven by the Test Clock (TCK) and the Test
Mode Select (TMS) pins. An independent power-on
reset circuit is provided to ensure the FSM is in the
TEST_LOGIC_RESET state at power-up. The FSM
is also reset when TMS and TDI are high for five
TCK periods.
Supported Instructions
In addition to the minimum IEEE 1149.1 requirements
(BYPASS, EXTEST, and SAMPLE instructions), three
additional
SETBYP) are provided to further ease board-level test-
ing. All unused instruction codes are reserved. See the
following table for a summary of supported instructions.
instructions
test
functions
(IDCODE,
implemented
TRIBYP
AMD
in
and
the
97