EVAL-AD5533EB AD [Analog Devices], EVAL-AD5533EB Datasheet - Page 14

• Manufacturer Part Number: EVAL-AD5533EB
• Description: 32-Channel Precision Infinite Sample-and-Hold
• Manufacturer: AD [Analog Devices]

AD5533B
readback, 16 bits of data are clocked out of the AD5533B on
each rising edge of SCLK and clocked into the DSP on the rising
edge of SCLK. D
centered in the 16-bit RX register when using this configuration.
The SPORT control register should be set up as follows:
TFSW
INVRFS = INVTFS = 1, Active Low Frame Signal
DTYPE = 00, Right-Justify Data
ISCLK = 1, Internal Serial Clock
TFSR
IRFS
ITFS
SLEN
SLEN
Figure 9 shows the connection diagram.
AD5533B to MC68HC11
The serial peripheral interface (SPI) on the MC68HC11 is config-
ured for master mode (MSTR = 1), clock polarity bit (CPOL) = 0
and the clock phase bit (CPHA) = 1. The SPI is configured by
writing to the SPI control register (SPCR)— see 68HC11 User
Manual. SCK of the 68HC11 drives the SCLK of the AD5533B,
the MOSI output drives the serial data line (D
and the MISO input is driven from D
derived from a port line (PC7). When data is being transmitted to
the AD5533B, the SYNC line is taken low (PC7). Data appear-
ing on the MOSI output is valid on the falling edge of SCK.
Serial data from the 68HC11 is transmitted in 8-bit bytes with
only eight falling clock edges occurring in the transmit cycle.
Data is transmitted MSB first. In order to transmit 10 data bits
in ISHA mode it is important to left-justify the data in the SPDR
register. PC7 must be pulled low to start a transfer. It is taken
high and pulled low again before any further read/write cycles
can take place. A connection diagram is shown in Figure 10.
*ADDITIONAL PINS OMITTED FOR CLARITY
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 9. AD5533B to ADSP-2101/ADSP-2103 Interface
AD5533B*
AD5533B*
Figure 10. AD5533B to MC68HC11 Interface
= RFSW = 1, Alternate Framing
= RFSR = 1, Frame Every Word
= 0, External Framing Signal
= 1, Internal Framing Signal
= 1001, 10-Bit Data-Words (ISHA Mode Write)
= 1111, 16-Bit Data-Words (Readback Mode)
SYNC
SCLK
SCLK
SYNC
D
D
OUT
OUT
IN
D
D
IN
IN
is ignored. The valid 14 bits of data will be
OUT
. The SYNC signal is
IN
MISO
PC7
SCK
MOSI
DR
TFS
RFS
DT
SCLK
) of the AD5533B,
MC68HC11*
ADSP-2101/
ADSP-2103*
–14–
AD5533B to PIC16C6x/7x
The PIC16C6x synchronous serial port (SSP) is configured as an
SPI Master with the clock polarity bit = 0. This is done by writing
to the Synchronous Serial Port Control Register (SSPCON). See
PIC16/17 Microcontroller User Manual. In this example I/O port
RA1 is being used to pulse SYNC and enable the serial port
of the AD5533B. This microcontroller transfers only eight bits of
data during each serial transfer operation; therefore, two consecu-
tive read/write operations are needed for a 10-bit write and a 14-bit
readback. Figure 11 shows the connection diagram.
AD5533B to 8051
The AD5533B requires a clock synchronized to the serial
data. The 8051 serial interface must therefore be operated in
Mode 0. In this mode, serial data enters and exits through RxD
and a shift clock is output on TxD. Figure 12 shows how the 8051
is connected to the AD5533B. Because the AD5533B shifts data
out on the rising edge of the shift clock and latches data in on
the falling edge, the shift clock must be inverted. The AD5533B
requires its data with the MSB first. Since the 8051 outputs
the LSB first, the transmit routine must take this into account.
APPLICATION CIRCUITS
AD5533B in a Typical ATE System
The AD5533B infinite sample-and-hold is ideally suited for use
in automatic test equipment. Several ISHAs are required to
control pin drivers, comparators, active loads, and signal timing.
Traditionally, sample-and-hold devices with droop were used in
these applications. These required refreshing to prevent the voltage
from drifting.
The AD5533B has several advantages: no refreshing is required,
there is no droop, pedestal error is eliminated, and there is no
need for extra filtering to remove glitches. Overall, a higher level
of integration is achieved in a smaller area. See Figure 13.
*ADDITIONAL PINS OMITTED FOR CLARITY
*ADDITIONAL PINS OMITTED FOR CLARITY
AD5533B*
AD5533B*
Figure 11. AD5533B to PIC16C6x/7x Interface
Figure 12. AD5533B to 8051 Interface
SYNC
SCLK
SCLK
SYNC
D
D
OUT
OUT
D
D
IN
IN
TXD
SCK/RC3
SDO/RC5
RA1
RXD
P1.1
SDI/RC4
PIC16C6x/7x*
8051*
REV. A