FTLF1328P2BNV FINISAR [Finisar Corporation.], FTLF1328P2BNV Datasheet
FTLF1328P2BNV
Related parts for FTLF1328P2BNV
FTLF1328P2BNV Summary of contents
Page 1
... Single 3.3V power supply • Extended operating temperature range: -5°C to 85°C Finisar’s FTLF1328P2BNV SFP+ transceivers are designed for use in Fibre Channel links 8.5 Gb/s data rate. These transceivers also support 4.25 Gb/s and 2.125 Gb/s. They are compliant with FC-PI-4 Rev. 8.00 3 and SFF-8472 Rev 10 ...
Page 2
... FTLF1328P2BNV Product Specification – October 2008 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS 4 SDA 2-wire Serial Interface Data Line (MOD-DEF2) 5 SCA 2-wire Serial Interface Clock (MOD-DEF1) ...
Page 3
... FTLF1328P2BNV Product Specification – October 2008 Pinout of Connector Block on Host Board II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing ...
Page 4
... FTLF1328P2BNV Product Specification – October 2008 Notes: 1. Non-condensing. 2. Module power consumption never exceeds 1W coupled open circuit. 5. Into 100 ohm differential termination – LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 8. All transceiver specifications are compliant with a power supply sinusoidal modulation 1.5 ...
Page 5
... FTLF1328P2BNV Product Specification – October 2008 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125 μm SMF , 2.125 Gb/s Max. Supported Link Length on 9/125 μm SMF , 4.25 Gb/s Max. Supported Link Length on 9/125 μm SMF , 8.5 Gb/s Notes: 1. 2x/4x/8x Fibre Channel compliant Tested with a PRBS 2 -1 test pattern ...
Page 6
... For more information, please see the SFP MSA documentation Note AN-2030. FTLF1328P2BNV transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. © ...
Page 7
... FTLF1328P2BNV Product Specification – October 2008 IX. Mechanical Specifications Finisar’s FTLF1328P2BNV SFP+ transceivers are compatible with the SFF-8432 specification for improved pluggable form factor. © Finisar Corporation October 30, 2008 Rev. A1 FTLF1328P2BNV Page 7 ...
Page 8
... FTLF1328P2BNV Product Specification – October 2008 X. PCB Layout and Bezel Recommendations © Finisar Corporation October 30, 2008 Rev Page 8 ...
Page 9
... FTLF1328P2BNV Product Specification – October 2008 © Finisar Corporation October 30, 2008 Rev Page 9 ...
Page 10
... FTLF1328P2BNV Product Specification – October 2008 XI. References 1. “Fibre Channel Physical Interface-4 Specification (FC-PI-4 Rev. 8.00)”. American National Standard for Information Technology, May 21, 2008. 2. “Improved Pluggable Formfactor”, SFF Document Number SFF-8432, Revision 5.0, July 16, 2007. 3. “Digital Monitoring Interface for Optical Transceivers”, SFF Document Number SFF-8472, Revision 10 ...