AFBR-732BE HP [Agilent(Hewlett-Packard)], AFBR-732BE Datasheet
![no-image](/images/no-image-200.jpg)
AFBR-732BE
Related parts for AFBR-732BE
AFBR-732BE Summary of contents
Page 1
... Agilent Component Field Sales office. AFBR-732B No EMI Nose Shield AFBR-742B No EMI Nose Shield AFBR-732BE With EMI Nose Shield AFBR-742BE With EMI Nose Shield Features • Low cost per Gb/s • High package density per Gb/s • ...
Page 2
... See Figure 1 for the transmitter and Figure 2 for the receiver block diagrams. The AFBR-732B transmitter and the AFBR-742B receiver modules provide very closely spaced, high-speed parallel data channels. Within these modules there will be some level of cross talk between channels ...
Page 3
DIN+ INPUT STAGE SHIFTER 12 DIN- 4 SERIAL CONTROLLER CONTROL I/O* Figure 1. Transmitter block diagram(each channel). * TX_EN, TX_DIS, RESET-, FAULT- PIN TRANS- IMPEDANCE PRE-AMPLIFIER Figure 2. Receiver block diagram (each channel). 3 SHUT AMPLIFIER DOWN LEVEL DRIVER ...
Page 4
... Normal handling precautions for electrostatic sensitive devices should be taken (see ESD section). The AFBR-732B is a Class 1M laser product. DO NOT VIEW RADIATION DIRECTLY WITH OPTICAL INSTRUMENTS. ...
Page 5
Absolute Maximum Ratings Parameter Storage Temperature (non-operating) Case Temperature (operating) Supply Voltage Data/Control Signal Input Voltage Transmitter Differential Data Input Voltage Output Current (dc) Relative Humidity (non-condensing) Notes: 1. Absolute Maximum Ratings are those values beyond which damage to ...
Page 6
Electrical Characteristics Transmitter Electrical Characteristics ( °C to +80 ° 3.3 V ± 5%, Typical Parameter Supply Current Power Dissipation Differential Input Impedance FAULT Assert Time RESET Assert Time RESET De-assert Time Transmit ...
Page 7
Receiver Electrical Characteristics ( °C to +80 ° 3.3 V ± 5%, Typical Parameter Supply Current Power Dissipation Differential Output Impedance Data Output Differential Peak-to-Peak Voltage Swing Inter-channel Skew Differential Data Output Rise/Fall ...
Page 8
Optical Characteristics Transmitter Optical Characteristics ( °C to +80 ° 3.3 V ± 5%, Typical Parameter Output Optical Power Output Optical Power – Off State Optical Modulation Amplitude Center Wavelength Spectral Width – ...
Page 9
Receiver Optical Characteristics ( °C to +80 ° 3.3 V ± 5%, Typical Parameter Input Optical Power Sensitivity (OMA) Input Optical Power Saturation (OMA) Operating Center Wavelength Stressed Receiver Sensitivity (OMA) Stressed Receiver ...
Page 10
Regulatory Compliance Table Feature Test Method Electrostatic Discharge JEDEC Human Body Model (HBM) (ESD) to the Electrical Pads (JESD22-A114-B) JEDEC Machine Model (MM) Electrostatic Discharge Variation of IEC 61000-4-2 (ESD) to the Connector Receptacle Electromagnetic FCC Part 15 CENELEC EN55022 ...
Page 11
Table 1. Transmitter Module Pad Description Symbol Functional Description V Transmitter Signal Common. All voltages are referenced to this potential unless otherwise indicated. Directly EE connect these pads to transmitter signal ground plane Transmitter Power Supply. Use recommended ...
Page 12
TRANSMITTER MODULE PAD ASSIGNMENT (TOWARD MTP® CONNECTOR DNC DNC DNC DNC DNC DNC DNC CCT CCT EE 4 DNC V V DIN3+ CCT CCT 5 DNC ...
Page 13
RECEIVER MODULE PAD ASSIGNMENT (TOWARD MTP® CONNECTOR DNC DNC DNC DNC DNC DOUT4- DOUT5+ CCR CCR EE 4 DNC V V DOUT3- ...
Page 14
Case Temperature Measurement Point Figure 3. Case temperature measurement. (label and heatsink removed for clarity) 25.0 20.0 15.0 No Heatsink Heatsink 10.0 5.0 0.0 0.5 0 1.0 1.5 Air Velocity (m/s) Figure 4. Case to Ambient thermal resistance (C/W) versus ...
Page 15
... V CCR V CCR V CCR V CCR V CCR V CCR NOTE DEFINED BY 3.135 < < 3.465 VOLTS AND THE POWER SUPPLY FILTER HAS < DROP ACROSS IT RESULTING IN 3.085 < V CCR < 3.415 VOLTS. Figure 5. Recommended receiver power supply filter. AFBR-732B V CCT V CCT V CCT V CCT V ...
Page 16
... C = 100 nF NOTE: AC COUPLING CAPACITORS SHOULD BE USED TO CONNECT DATA OUTPUTS TO DATA INPUTS BETWEEN THE AFBR-732B, AFBR-742B, AND HOST BOARD ICs (e.g., ASIC) WITH EITHER 50 W SINGLE-ENDED OR 100 Ω DIFFERENTIAL TERMINATIONS AS SHOWN. THE CAPACITORS' VALUES CAN BE REDUCED FROM 100 nF (0603 SIZE) IF THE DATA RATE AND RUN LENGTH ARE LIMITED. ...
Page 17
MIN KEEP-OUT ∅ 0 ∅ 2.69 ± 0.05 HOLES FOR #2 SCREW ∅ 0.1 A B-C 18.42 MIN. 50 KEEP-OUT AREA FOR MPO CONNECTOR NOTE: The host electrical connector attached ...
Page 18
V CCR 50 Ω 50 Ω Figure 10. Rx data output equivalent circuit. V > 2 ~6.5 ms SHUTDOWN TX OUT 0 ~4 OUT 1 SHUTDOWN ~4.6 ms SHUTDOWN TX OUT 2 ...
Page 19
RESET FAULT > 100 ns ~ OUT 0 SHUTDOWN ~4 OUT 1 ~4 OUT 2 TX OUT 11 ~5 µs (Toff) Figure 14. Transmitter RESET timing diagram. TX_EN ~5 µs (Toff) TX ...
Page 20
... Module Outline Notes: 1. Module supplied with port process plug. 2. Module mass approximately 20 grams. Figure 16. Package outline for AFBR-732B and AFBR-742B (dimensions in mm). 20 ...
Page 21
... Notes: 1. Module supplied with port process plug. 2. Module mass approximately 20 grams. Figure 17. Package Outline for AFBR-732BE and AFBR-742BE (dimensions in mm) 21 ...
Page 22
Figure 18. Host Frontplate Layout (dimensions in mm) www.agilent.com/ semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 ...