LUCL8574DP-D AGERE [Agere Systems], LUCL8574DP-D Datasheet - Page 6

• Manufacturer Part Number: LUCL8574DP-D
• Description: L8574D Resistive Subscriber Line Interface Circuit(SLIC), Ring Relay,and Protector(SRP)for Long Loop and TR-57 Applications
• Manufacturer: AGERE [Agere Systems]

L8574D Resistive Subscriber Line Interface Circuit (SLIC), Ring
Relay, and Protector (SRP) for Long Loop and TR-57 Applications
Pin Information
Table 1. Pin Descriptions (continued)
On the printed-wiring board (PWB), make the leads to FGND and V
reasons. Also, maximize the amount of PWB copper on all leads connected to this device for the lowest operating
temperature.
Absolute Maximum Ratings
(@ T
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are abso-
lute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess
of those indicated in the operational sections of this data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect device reliability.
Notes:
Analog voltages (V
The IC can be damaged unless all ground connections are applied before, and removed after, all other connections. Furthermore, when power-
ing the device, the user must guarantee that no external potential creates a voltage on any pin of the device that exceeds the device ratings. For
example, inductance in a supply lead could resonate with the supply filter capacitor to cause a destructive overvoltage.
6
+5 V dc Supplies (V
Office Battery Supply
Logic Input Voltage
Logic Input Clamp Diode Current, per Pin
Logic Output Voltage
Logic Output Current, per Pin (excluding relay driver)
Operating Temperature Range
Storage Temperature Range
Relative Humidity Range
Ground Potential Difference (DGND to AGND)
Pin
33
34
35
36
38
40
41
42
43
44
A
= 25 C)
Symbol
AGND
RCVN
CLIM
V
V
V
XMT
PTA
RS
TS
CCA
BAT2
BAT1
CCA
, V
BAT1
CCA
(continued)
Parameter
, and V
& V
Type
—
—
—
—
—
O
I
I
I
I
DD
BAT2
)
) are referenced to AGND, and digital (logic) voltages (V
Current Limiter Capacitor. Connect a 0.1 F capacitor from this pin to pin V
Office Battery Supply. Negative high-voltage power supply.
Analog Ground. Ground return for analog circuitry.
+5 V Analog dc Supply. +5 V supply for analog circuitry.
Protected Tip A. Connect to PT via an external coupling network.
Office Battery Supply. Negative high-voltage power supply.
Transmit Signal Output. Transmit amplifier output to codec.
Tip Sense. Negative (–) input of transmit op amp. Connect one high-value resis-
tor between TS and the Tip of the loop and another high-value resistor between
TS and XMT.
Ring Sense. Positive (+) input of the transmit op amp. Connect one high-value
resistor between RS and the Ring of the loop and another high-value resistor
between RS and AGND (see the application diagram, Figure 5).
Receive Signal Input (–). The differential current flowing from PT to PR is –200
times the voltage applied to RCVN divided by the impedance connected
between IRCV and AGND.
Symbol
V
V
T
—
BAT1
BAT2
—
—
—
—
—
—
—
stg
Name/Function
BF
as wide as possible for thermal and electrical
–0.5
–0.5
–0.5
Min
–63
–63
–40
–40
—
—
—
5
DD
) are referenced to DGND.
Typ
—
—
—
—
—
—
—
—
20
35
3
Lucent Technologies Inc.
V
V
DD
DD
Max
125
125
7.0
0.5
0.5
95
—
—
—
+ 0.5
+ 0.5
October 1998
Data Sheet
Unit
mA
mA
%
V
V
V
V
V
V
C
C
BF
.