88-00151-00 Murata Wireless Solutions, 88-00151-00 Datasheet - Page 26

• Manufacturer Part Number: 88-00151-00
• Description: WiFi / 802.11 Modules SN8200 Wifi Network Controller Module
• Manufacturer: Murata Wireless Solutions

Specifications of 88-00151-00

• Rohs: yes
• Protocol Supported: 802.11 b/g/n
• Frequency Band: 2.4 GHz
• Data Rate: 11 Mbps, 54 Mbps
• Interface Type: I2C, SPI, UART
• Transmit Power (max): 18 dBm
• Antenna Connector Type: On-board
• Operating Supply Voltage: 3.3 V
• Supply Current Transmitting: 370 mA
• Supply Current Receiving: 110 mA
• Maximum Operating Temperature: + 85 C
• Dimensions: 30.5 mm x 19.4 mm x 2.8 mm
• Minimum Operating Temperature: - 30 C
• Modulation Technique: CCK, DSSS
• Tradename: SyNode

Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son
utilisation est soumise à Les deux conditions suivantes: (1) cet appareil ne peut pas provoquer
d'interférences et (2) cet appareil doit accepter Toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
This device complies with Health Canada’s Safety Code 6 / IC RSS-210. The installer of this device
should ensure that RF radiation is not emitted in excess of the Health Canada’s requirement.
Information can be obtained at:
lignes_direct-eng.php
Cet appareil est conforme avec Santé Canada Code de sécurité 6 / IC RSS-210. Le programme
d'installation de cet appareil doit s'assurer que les rayonnements RF n'est pas émis au-delà de
l'exigence de Santé Canada. Les informations peuvent être obtenues: http://www.hc-sc.gc.ca/ewh-
semt/pubs/radiation/radio_guide-lignes_direct-eng.php
The host device should be properly labeled to identify the module within the host device. The
Industry Canada certification label of a module shall be clearly visible at all times when installed in
the host device, otherwise the host device must be labeled to display the Industry Canada
certification number of the module, preceded by the words “Contains transmitter module”, or the
word “Contains”, or similar wording expressing the same meaning, as follows:
Contains transmitter module IC:4523A-SN8200,
where 4523A-SN8200 is the module’s certification number.
This device has been tested and certified for use in the European Union.
If this device is used in a product, the OEM has responsibility to verify compliance of the final
product to the EU standards. A Declaration of Conformity must be issued and kept on file as
described in Annex II of the Radio and Telecommunications Terminal Equipment Directive.
The ‘CE’ mark must be placed on the OEM product per the labeling requirements of the Directive.
Given that the operating frequency band is not harmonized by a few European countries, the
restriction or alert sign must be placed alongside the ‘CE’ mark as shown below. As of the date of
this document, only France has a restriction. The restriction is that, if the radio is operated outdoors
in the 2450-2483.5 MHz band, the power must be limited to 10 mW instead of 100 mW. The OEM
must account for this and the product must have the alert mark. It does not require country
notifications, however.
11.5 IC Labeling Requirements
11.6 CE Notice (Europe)
11.7 CE Labeling Requirements
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-
Page 26 of 29
SN8200 User Manual and Datasheet v1.1