C8051F349-GMR Silicon Labs, C8051F349-GMR Datasheet - Page 170
C8051F349-GMR
Manufacturer Part Number
C8051F349-GMR
Description
8-bit Microcontrollers - MCU 25 MIPS 32KB USB MCU
Manufacturer
Silicon Labs
Datasheet
1.C8051F349-GMR.pdf
(276 pages)
Specifications of C8051F349-GMR
Rohs
yes
Core
8051
Processor Series
C8051
Data Bus Width
8 bit
- Current page: 170 of 276
- Download datasheet (2Mb)
C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
“14. Oscillators” on page 131
mode feature of the internal oscillator.
USB0 exits Suspend mode when any of the following occur: (1) Resume signaling is detected or gener-
ated, (2) Reset signaling is detected, or (3) a device or USB reset occurs. If suspended, the internal oscil-
lator will exit Suspend mode upon any of the above listed events.
Resume Signaling: USB0 will exit Suspend mode if Resume signaling is detected on the bus. A Resume
interrupt will be generated upon detection if enabled (RESINTE = ‘1’). Software may force a Remote
Wakeup by writing ‘1’ to the RESUME bit (POWER.2). When forcing a Remote Wakeup, software should
write RESUME = ‘0’ to end Resume signaling 10-15 ms after the Remote Wakeup is initiated (RESUME =
‘1’).
ISO Update: When software writes ‘1’ to the ISOUP bit (POWER.7), the ISO Update function is enabled.
With ISO Update enabled, new packets written to an ISO IN endpoint will not be transmitted until a new
Start-Of-Frame (SOF) is received. If the ISO IN endpoint receives an IN token before a SOF, USB0 will
transmit a zero-length packet. When ISOUP = ‘1’, ISO Update is enabled for all ISO endpoints.
USB Enable: USB0 is disabled following a Power-On-Reset (POR). USB0 is enabled by clearing the
USBINH bit (POWER.4). Once written to ‘0’, the USBINH can only be set to ‘1’ by one of the following: (1)
a Power-On-Reset (POR), or (2) an asynchronous USB0 reset generated by writing ‘1’ to the USBRST bit
(POWER.3).
Software should perform all USB0 configuration before enabling USB0. The configuration sequence
should be performed as follows:
170
Step 1. Select and enable the USB clock source.
Step 2. Reset USB0 by writing USBRST= ‘1’.
Step 3. Configure and enable the USB Transceiver.
Step 4. Perform any USB0 function configuration (interrupts, Suspend detect).
Step 5. Enable USB0 by writing USBINH = ‘0’.
for more details on internal oscillator configuration, including the Suspend
Rev. 1.3
Related parts for C8051F349-GMR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: