72V3640L15PF IDT, 72V3640L15PF Datasheet - Page 17
![no-image](/images/no-image-200.jpg)
72V3640L15PF
Manufacturer Part Number
72V3640L15PF
Description
FIFO
Manufacturer
IDT
Datasheet
1.72V3690L6PFG.pdf
(46 pages)
Specifications of 72V3640L15PF
Part # Aliases
IDT72V3640L15PF
SERIAL PROGRAMMING MODE
programming of PAE and PAF values can be achieved by using a combination
of the LD, SEN, WCLK and SI input pins. Programming PAE and PAF proceeds
as follows: when LD and SEN are set LOW, data on the SI input are written,
one bit for each WCLK rising edge, starting with the Empty Offset LSB and ending
with the Full Offset MSB. A total of 20 bits for the IDT72V3640, 22 bits for the
IDT72V3650, 24 bits for the IDT72V3660, 26 bits for the IDT72V3670, 28 bits
for the IDT72V3680 and 30 bits for the IDT72V3690. See Figure 15, Serial
Loading of Programmable Flag Registers, for the timing diagram for this mode.
selectively. PAE and PAF can show a valid status only after the complete set
of bits (for all offset registers) has been entered. The registers can be
reprogrammed as long as the complete set of new offset bits is entered. When
LD is LOW and SEN is HIGH, no serial write to the registers can occur.
programming sequence. In this case, the programming of all offset bits does
not have to occur at once. A select number of bits can be written to the SI input
and then, by bringing LD and SEN HIGH, data can be written to FIFO memory
via D
restored to a LOW, the next offset bit in sequence is written to the registers via
SI. If an interruption of serial programming is desired, it is sufficient either to set
LD LOW and deactivate SEN or to set SEN LOW and deactivate LD. Once LD
and SEN are both restored to a LOW level, serial offset programming continues.
will be valid until the full set of bits required to fill all the offset registers has been
written. Measuring from the rising WCLK edge that achieves the above criteria;
PAF will be valid after two more rising WCLK edges plus t
after the next two rising RCLK edges plus t
PARALLEL MODE
programming of PAE and PAF values can be achieved by using a combination
of the LD, WCLK , WEN and D
proceeds as follows: LD and WEN must be set LOW. For x36 bit input bus width,
data on the inputs D
to-HIGH transition of WCLK. Upon the second LOW-to-HIGH transition of
WCLK, data are written into the Full Offset Register. The third transition of WCLK
writes, once again, to the Empty Offset Register. For x18 bit input bus width,
data on the inputs Dn are written into the Empty Offset Register LSB on the first
LOW-to-HIGH transition of WCLK. Upon the 2nd LOW-to-HIGH transition of
WCLK data are written into the Empty Offset Register MSB. The third transition
of WCLK writes to the Full Offset Register LSB, the fourth transition of WCLK then
writes to the Full Offset Register MSB. The fifth transition of WCLK writes once
again to the Empty Offset Register LSB. A total of four writes to the offset registers
is required to load values using a x18 input bus width. For an input bus width
of x9 bits, a total of six write cycles to the offset registers is required to load values.
See Figure 3, Programmable Flag Offset Programming Sequence. See
Figure 16, Parallel Loading of Programmable Flag Registers, for the timing
diagram for this mode.
pointer. The act of reading offsets employs a dedicated read offset register
pointer. The two pointers operate independently; however, a read and a write
should not be performed simultaneously to the offset registers. A Master Reset
initializes both pointers to the Empty Offset (LSB) register. A Partial Reset has
no effect on the position of these pointers.
IDT72V3640/50/60/70/80/90 3.3V HIGH DENSITY SUPERSYNC II
1,024 x 36, 2,048 x 36, 4,096 x 36, 8,192 x 36, 16,384 x 36 and 32,768 x 36
If Serial Programming mode has been selected, as described above, then
Using the serial method, individual registers cannot be programmed
Write operations to the FIFO are allowed before and during the serial
From the time serial programming has begun, neither programmable flag
It is only possible to read the flag offset values via the parallel output port Qn.
If Parallel Programming mode has been selected, as described above, then
The act of writing offsets in parallel employs a dedicated write offset register
n
by toggling WEN. When WEN is brought HIGH with LD and SEN
n
are written into the Empty Offset Register on the first LOW-
n
input pins. Programming PAE and PAF
PAE
plus t
SKEW2
PAF
, PAE will be valid
.
TM
17
36-BIT FIFO
programming sequence. In this case, the programming of all offset registers does
not have to occur at one time. One, two or more offset registers can be written
and then by bringing LD HIGH, write operations can be redirected to the FIFO
memory. When LD is set LOW again, and WEN is LOW, the next offset register
in sequence is written to. As an alternative to holding WEN LOW and toggling
LD, parallel programming can also be interrupted by setting LD LOW and
toggling WEN.
during the programming process. From the time parallel programming has
begun, a programmable flag output will not be valid until the appropriate offset
word has been written to the register(s) pertaining to that flag. Measuring from
the rising WCLK edge that achieves the above criteria; PAF will be valid after
two more rising WCLK edges plus t
RCLK edges plus t
register pointer. The contents of the offset registers can be read on the Q
pins when LD is set LOW and REN is set LOW. For x36 output bus width, data
are read via Q
transition of RCLK. Upon the second LOW-to-HIGH transition of RCLK, data are
read from the Full Offset Register. The third transition of RCLK reads, once again,
from the Empty Offset Register. For x18 output bus width, a total of four read
cycles are required to obtain the values of the offset registers. Starting with the
Empty Offset Register LSB and finishing with the Full Offset Register MSB. For
x9 output bus width, a total of six read cycles must be performed on the offset
registers. See Figure 3, Programmable Flag Offset Programming Sequence.
See Figure 17, Parallel Read of Programmable Flag Registers, for the timing
diagram for this mode.
writes to the FIFO. The interruption is accomplished by deasserting REN, LD,
or both together. When REN and LD are restored to a LOW level, reading of
the offset registers continues where it left off. It should be noted, and care should
be taken from the fact that when a parallel read of the flag offsets is performed,
the data word that was present on the output lines Qn will be overwritten.
which timing mode (IDT Standard or FWFT modes) has been selected.
RETRANSMIT OPERATION
accessed again. There are 2 modes of Retransmit operation, normal latency
and zero latency. There are two stages to Retransmit: first, a setup procedure
that resets the read pointer to the first location of memory, then the actual
retransmit, which consists of reading out the memory contents, starting at the
beginning of memory.
REN and WEN must be HIGH before bringing RT LOW. When zero latency
is utilized, REN does not need to be HIGH before bringing RT LOW. At least
two words, but no more than D - 2 words should have been written into the FIFO,
and read from the FIFO, between Reset (Master or Partial) and the time of
Retransmit setup. D = 1,024 for the IDT72V3640, 2,048 for the IDT72V3650,
4,096 for the IDT72V3660, 8,192 for the IDT72V3670, 16,384 for the
IDT72V3680 and 32,768 for the IDT72V3690. In FWFT mode, D = 1,025 for
the IDT72V2640, 2,049 for the IDT72V3650, 4,097 for the IDT72V3660, 8,193
for the IDT72V3670, 16,385 for the IDT72V3680 and 32,769 for the IDT72V3690.
Retransmit setup by setting EF LOW. The change in level will only be noticeable
Write operations to the FIFO are allowed before and during the parallel
Note that the status of a programmable flag (PAE or PAF) output is invalid
The act of reading the offset registers employs a dedicated read offset
It is permissible to interrupt the offset register read sequence with reads or
The Retransmit operation allows data that has already been read to be
Retransmit setup is initiated by holding RT LOW during a rising RCLK edge.
If IDT Standard mode is selected, the FIFO will mark the beginning of the
Parallel reading of the offset registers is always permitted regardless of
n
from the Empty Offset Register on the first LOW-to-HIGH
PAE
plus t
SKEW2
PAF
COMMERCIAL AND INDUSTRIAL
.
, PAE will be valid after the next two rising
TEMPERATURE RANGES
OCTOBER 22, 2008
0
-Q
n