CAT1641WI-25-G ON Semiconductor, CAT1641WI-25-G Datasheet - Page 4

• Manufacturer Part Number: CAT1641WI-25-G
• Description: Supervisory Circuits CPU w/64K
• Manufacturer: ON Semiconductor

Specifications of CAT1641WI-25-G

• Product Category: Supervisory Circuits
• Rohs: yes
• Number Of Voltages Monitored: 1
• Monitored Voltage: 3 V, 3.3 V, 5 V
• Undervoltage Threshold: 2.55 V
• Overvoltage Threshold: 2.7 V
• Output Type: Active High, Open Drain
• Manual Reset: Resettable
• Watchdog: No Watchdog
• Battery Backup Switching: No Backup
• Power-up Reset Delay (typ): 270 ms
• Supply Voltage - Max: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SOIC-8 Wide
• Chip Enable Signals: No
• Maximum Power Dissipation: 1000 mW
• Minimum Operating Temperature: - 40 C
• Power Fail Detection: No
• Supply Current (typ): 3000 uA
• Supply Voltage - Min: 3 V

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Output shorted for no more than one second. No more than one output shorted at a time.
2. This parameter is tested initially and after a design or process change that affects the parameter. Not 100% tested.
3. V
Temperature Under Bias
Storage Temperature
Voltage on any Pin with Respect to Ground (Note 1)
V
Package Power Dissipation Capability (T
Lead Soldering Temperature (10 seconds)
Output Short Circuit Current (Note 1)
Table 4. ABSOLUTE MAXIMUM RATINGS
V
Table 5. D.C. OPERATING CHARACTERISTICS
V
CC
RVALID
CC
V
V
V
IL
RT
IH
IL
with Respect to Ground
Symbol
= +3.0 V to +5.5 V and over the recommended temperature conditions unless otherwise specified.
min and V
(Note 3)
I
I
(Note 3)
V
V
V
(Note 2)
I
CC1
CC2
I
I
SB
LO
OH
LI
OL
TH
(Note 2)
IH
max are reference values only and are not tested.
Input Leakage Current
Output Leakage Current
Power Supply Current (Write)
Power Supply Current (Read)
Standby Current
Input Low Voltage
Input High Voltage
Output Low Voltage
(SDA, RESET)
Output High Voltage
(RESET)
Reset Threshold
Reset Output Valid V
Reset Threshold Hysteresis
Parameters
Parameter
A
CC
= 25°C)
Voltage
SPECIFICATIONS
http://onsemi.com
V
V
f
V
f
V
V
V
I
V
I
V
CAT164x−45
(V
CAT164x−42
(V
CAT164x−30
(V
CAT164x−28
(V
CAT164x−25
(V
SCL
SCL
OL
OH
IN
IN
CC
CC
CC
IN
CC
CC
CC
CC
CC
CC
CC
4
= 3 mA
= GND to V
= GND to V
= GND or V
= −0.4 mA
Test Conditions
= 400 kHz
= 5.5 V
= 400 kHz
= 5.5 V
= 5.5 V
= 3.0 V
= 3.0 V
= 5.0 V)
= 5.0 V)
= 3.3 V)
= 3.3 V)
= 3.0 V)
CC
CC
CC
V
−0.5 to V
0.7 x V
CC
−0.5
4.50
4.25
3.00
2.85
2.55
1.00
–65 to +105
−0.5 to +7.0
Min
−10
–40 to +85
−2
15
− 0.75
Ratings
300
100
CC
1.0
CC
+ 2.0
Typ
V
0.3 x V
CC
Max
4.75
4.50
3.15
3.00
2.70
0.4
10
10
40
3
1
+ 0.5
CC
Units
Units
mA
°C
°C
°C
mA
mA
mV
W
mA
mA
mA
V
V
V
V
V
V
V
V