M93S46-WMN6TP STMicroelectronics, M93S46-WMN6TP Datasheet - Page 5

• Manufacturer Part Number: M93S46-WMN6TP
• Description: IC EEPROM 1KBIT 2MHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M93S46-WMN6TP

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 1K (64 x 16)
• Speed: 2MHz
• Interface: Microwire, 3-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Organization: 64 K x 16
• Interface Type: Microwire
• Maximum Clock Frequency: 2 MHz
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 2 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 3.3 V, 5 V
• Density: 1Kb
• Frequency (max): 2MHz
• Write Protection: Yes
• Data Retention: 40Year
• Operating Supply Voltage (typ): 3.3/5V
• Package Type: SOIC N
• Operating Temp Range: -40C to 85C
• Supply Current: 2mA
• Operating Supply Voltage (min): 2.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8666-2; M93S46-WMN6TP

An internal Power-on Data Protection mechanism
in the M93Sx6 inhibits the device when the supply
is too low.
POWER-ON DATA PROTECTION
To prevent data corruption and inadvertent write
operations during power-up, a Power-On Reset
(POR) circuit resets all internal programming cir-
cuitry, and sets the device in the Write Disable
mode.
–
–
For the M93Sx6 devices (5V range) the POR
threshold voltage is around 3V. For the M93Sx6-
W (3V range) and M93Sx6-R (2V range) the POR
threshold voltage is around 1.5V.
At Power-up and Power-down, the device
must not be selected (that is, Chip Select Input
(S) must be driven Low) until the supply
voltage reaches the operating value V
specified in
When V
properly reset (in the Write Disable mode) and
is ready to decode and execute incoming
instructions.
CC
reaches its valid level, the device is
Table 5.
to
Table
6..
CC
INSTRUCTIONS
The instruction set of the M93Sx6 devices con-
tains seven instructions, as summarized in
2.
lowing parts, as shown in
The M93Sx6 devices are fabricated in CMOS
technology and are therefore able to run as slow
as 0 Hz (static input signals) or as fast as the max-
imum ratings specified in
to
Each instruction is preceded by a rising edge
on Chip Select Input (S) with Serial Clock (C)
being held Low.
A start bit, which is the first ‘1’ read on Serial
Data Input (D) during the rising edge of Serial
Clock (C).
Two op-code bits, read on Serial Data Input
(D) during the rising edge of Serial Clock (C).
(Some instructions also use the first two bits of
the address to define the op-code).
The address bits of the byte or word that is to
be accessed. For the M93S46, the address is
made up of 6 bits (see
M93S56 and M93S66, the address is made up
of 8 bits (see
Table
3.. Each instruction consists of the fol-
Table
M93S66, M93S56, M93S46
3.).
Table 16.
Figure
Table
4.:
2.). For the
to
Table
Table
19..
5/34