GLS85LD1001T-60-RI-40CN-K Greenliant, GLS85LD1001T-60-RI-40CN-K Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/2/284/greenliant_sml.jpg)
GLS85LD1001T-60-RI-40CN-K
Manufacturer Part Number
GLS85LD1001T-60-RI-40CN-K
Description
Memory IC Development Tools 1GB NANDrive Eval Bd 40-pin ATA Connector
Manufacturer
Greenliant
Datasheet
1.GLS85LP1002P-S-I-44CN-K.pdf
(11 pages)
Specifications of GLS85LD1001T-60-RI-40CN-K
Rohs
yes
2
2.1
2.2
© 2011 Greenliant Systems
03/18/2011
S74015
Perform these three tasks to install the evaluation board:
The evaluation board easily connects to any desktop PC with a parallel ATA interface.
To connect the board:
When you power on the PC, the BIOS should detect and report the correct density of the NANDrive attached to
the evaluation board. If the BIOS does not detect the NANDrive, follow the power on procedures below.
To power on the PC:
Table 2: IDE Mode Settings
Ultra-DMA mode: Not supported
1. Connect board to PC
2. Detect the device
3. Add a new drive
1. Turn off the PC.
2. Open the PC chassis.
3. If your evaluation board has a 40-pin ATA connector, connect the peripheral power cable to J2 on the
4. Connect the PC IDE cable to CN1 on the evaluation board. If necessary, use an existing connector on a
5. Set JP1 to either Master or Slave on the evaluation board. If another device uses the same IDE cable as
1. Turn on the PC. If the BIOS detects the NANDrive, stop. If it does not detect the NANDrive, go to step 2.
2. Wait until LED D1 on the evaluation board begins to quickly blink. This indicates that initialization has
3. Reboot the PC. If the BIOS detects the NANDrive, stop. If it does not detect the NANDrive, go to step 4.
4. Check that the BIOS IDE settings are set to Auto Detect and the IDE mode is set as shown in Table 2
5. If after executing all the above steps the BIOS does not detect the NANDrive, contact Greenliant for
Ultra-DMA mode: Supported
Ultra-DMA mode: Supported
PATA NANDrive™ Evaluation Board
(LD020 based NANDrive)
(LD040 based NANDrive)
Install the Evaluation Board
CAUTION:
CAUTION:
a)
b)
Connect Board to PC
evaluation board. If your evaluation board has a 44-pin connector, no additional connections are required
because the PC supplies power to the device through pins 41 and 42 on the connector.
used ATA cable.
the NANDrive, one device must be set as Master and the other as Slave.
Detect the Device
completed successfully.
below.
support.
User Guide
PATA NANDrive is capable of supporting PIO Mode-6 but Identify drive information report as PIO Mode-4
PATA NANDrive is capable of supporting Multi-Word DMA Mode-4 but Identify drive information report as MWDMA Mode-2
Product Type
Ensure that the power is off before connecting /disconnecting any devices to your PC.
Failure to do so can damage the PC and the evaluation board.
Static electricity can damage electronic devices. To prevent static damage, discharge static
electricity before you touch any electronic components.
Multi-Word DMA mode4
Multi-Word DMA mode4, PIO mode6
7
Multi-Word DMA Mode2 or PIO mode4
Windows is a trademark of Microsoft Corporation in the United States and other countries
Greenliant, the Greenliant logo and NANDrive are trademarks of Greenliant Systems
Mode Settings
b)
, PIO mode6
These specifications are subject to change without notice.
a)
a)
or Ultra-DMA mode4
or Ultra-DMA mode6
Application Note
March 2011