Si2439-A-FM18-EVB Silicon Labs, Si2439-A-FM18-EVB Datasheet
![no-image](/images/no-image-200.jpg)
Si2439-A-FM18-EVB
Manufacturer Part Number
Si2439-A-FM18-EVB
Description
Networking Development Tools 38pin Si2439+ Si3018 ISOmodem Eval Board
Manufacturer
Silicon Labs
Type
Network Controller & Processorr
Datasheet
1.SI2439-A-FM18-EVB.pdf
(36 pages)
Specifications of Si2439-A-FM18-EVB
Rohs
yes
Tool Is For Evaluation Of
Si2439
Data Rate
56 Kbps
Interface Type
RJ-11, RS-232, SPI, UART, USB
Operating Supply Voltage
3.3 V
E v a l u a t i o n B o a r d R e v 5 . 0 f o r t h e S i 2 4 9 3 / 5 7 / 3 4 / 1 5 / 0 4
I S O m o d e m w i t h U A R T a n d S P I I n t e r f a c e s
Description
The global Si2493/57/34/15/04-EVB evaluation board
Rev 5.0 provides the system designer an easy way of
evaluating the Si2493/57/34/15/04 ISOmodem
Si2493/57/34/15/04-EVB consists of a motherboard
with a power supply, an RS-232 and USB interface,
other ease-of-use features, and a complete removable
modem module on a daughter card. (A functional block
diagram of the Si2493/57/34/15/04-EVB is shown
below.) The Si2493/57/34/15/04 ISOmodem is a
complete controller-based modem chipset with an
integrated
arrangement (DAA) that meets global telephone line
requirements. Available as a combination of one 16-pin
small line-side device and one 24-pin or 16-pin system-
side
eliminates the need for a separate DSP data pump,
modem
transformer, relays, opto-isolators, and a 2- to 4-wire
hybrid. The Si2493/57/34/15/04 is ideal for embedded
modem applications due to its small board area,
controller-based architecture, low power consumption,
and global compliance. The Si2493/57/34/15/04-EVB
provides an RJ-11 jack (for interfacing the Si2493/57/
34/15/04-EVB to the phone line), and USB and RS232
serial ports for interfacing to a PC or data terminal. This
allows the ISOmodem to operate as a serial modem for
straightforward evaluation of the Si2493/57/34/15/04. To
evaluate the Si2493/57/34/15/04 ISOmodem in an
embedded system, the daughter card can be used
independently of or with the motherboard.
Functional Block Diagram
Rev. 0.7 4/11
device,
controller,
Connector
UART
and
USB
the
7.5-13.5 V dc or
peak ac Adaptor
DB9
Rectifier
programmable
Filter
Si2493/57/34/15/04
USB I/F
memories,
Transceivers
Regulator
RS-232
Voltage
5 V
Copyright © 2011 by Silicon Laboratories
codec,
3.3 V
direct
Selection
Interface
Jumpers
Push Button
Power-On
Reset
Reset
ISOmodem
Access HDR
G l o b a l I S O m o d e m - E V B
isolation
Direct
®
access
. The
RESET
Si2493/57/34/15/04
XTALO
A direct access header (J103) is available on the
motherboard to bypass the RS-232 transceivers and
connect the Si2493/57/34/15/04 ISOmodem directly to
a target system.
An on-board rectifier, filter, and voltage regulator allow
the power input to be 7.5–13 V ac or dc (either polarity)
supplied through a screw terminal (J8) or a standard
2 mm power jack (J9). Alternatively, power can be
supplied through the USB interface (whether the USB or
RS232 interface is used). The evaluation board can
drive an external speaker for call monitoring or the
speaker mounted directly on the board. Please note that
the PCM interface, parallel interface, and EEPROM are
available on the 24-pin FT only. See "1.7.EVB Part
Numbers" on page 8 for ISOmodem EVB options.
Features
The Si2493/57/34/15/04-EVB includes the following:
S i 2 4 9 3 / 5 7 / 3 4 / 1 5 / 0 4
Dual RJ-11 connection to phone line
RS-232 and USB interface to PC
Speaker for call monitoring
Direct access to Si2493/57/34/15/04 for embedded
application evaluation
Easy power connection to common 7.5 V–13.5 V
power supplies or USB port.
9 V ac adaptor
Simple installation and operation
EEPROM (24-pin FT only)
RS232 lines status display on LEDs.
Amplifier
*Si3010 for Si2404
XTALI
Audio
AOUT
Audio
Out
Daughter Board Boundary
Si3018*
Interface
Circuit
Si2493/57/34/15/04-EVB
RJ-11
Phone
line