EM357-MOD-LR-ANT-T Silicon Labs, EM357-MOD-LR-ANT-T Datasheet - Page 22
![no-image](/images/no-image-200.jpg)
EM357-MOD-LR-ANT-T
Manufacturer Part Number
EM357-MOD-LR-ANT-T
Description
Zigbee / 802.15.4 Modules EM357 Module, w/ PA /LNA, incl. antenna
Manufacturer
Silicon Labs
Datasheet
1.EM357-MOD-LR-ANT-T.pdf
(43 pages)
Specifications of EM357-MOD-LR-ANT-T
Rohs
yes
Frequency Band
2.4 GHz
Data Rate
500 Kbps
Sensitivity
- 100 dBm
Supply Current Transmitting
31 mA
Supply Current Receiving
26 mA
Maximum Operating Temperature
+ 85 C
Dimensions
7.12 mm x 7.12 mm x 1 mm
EM35x Development Kit User Guide
4.3
To avoid communication problems, verify that each radio communication module is firmly seated in its Breakout
Board connector, and its InSight port cable is properly seated.
4.4
Refer to document 120-4031-000, Quick Start Guide, included in your development kit for detailed step-by-step
instructions for setting up your hardware.
Two hardware modules attach to the EM35x Breakout Board:
•
•
To attach the radio communication module:
Align the radio communication module to its footprint outline on the Breakout Board, and then press it into
place. Make sure that the RCM sits firmly in its mating connector.
To remove the radio communication module:
•
To attach the InSight Adapter:
1
2
3
To remove the InSight Adapter:
1
2
Silicon Labs Part Number
EM357-MOD-ANT-T
EM357-MOD-RF-T
EM357-MOD-LR-RF-T
EM357-MOD-LR-AN-T
EM351-MOD-ANT-T
EM351-MOD-RF-T
EM351-MOD-LR-RF-T
EM351-MOD-LR-AN-T
Caution:
communication modules.
Radio Communication Module (RCM)
InSight Adapter
Carefully pull the RCM away from the Breakout Board.
Plug the InSight Port cable into the InSight Adapter.
Plug one end of the InSight Port cable into the 10 pin InSight Port (J31) on the Breakout Board, and the
other end into the ISA. If desired, the InSight Port cable may be connected directly to the RCM instead of
the Breakout Board, but the Breakout Board connector allows for straight cable paths and more convenient
swapping of modules.
Verify that the InSight Adapter’s Target Power Select switch is set to Int (Internal).
Unplug the InSight Port cable from the Breakout Board (or radio communication module).
Unplug the InSight Port cable from the InSight Adapter.
Hardware Connections
Connecting the Breakout Board and RCM
Observe electrostatic discharge (ESD) precautions when removing, handling, or replacing RF
Telegesis Part Number
ETRX357+CB
ETRX357-HR+CB
ETRX357-LRS-HR+CB
ETRX357-LRS+CB
ETRX351+CB
ETRX351-HR+CB
ETRX351-LRS-HR+CB
ETRX351-LRS+CB
Table 4-1. Module Product Variant Matrix
Product
Number
Silicon
Labs
0720
0721
0722
0723
0724
0725
0726
0727
EM357
EM357
EM357
EM357
EM351
EM351
EM351
EM351
IC
Antenna or
Connector
Connector
Connector
Connector
Connector
Antenna
Antenna
Antenna
Antenna
non-PA
Non-PA
Non-PA
Non-PA
Non-PA
PA or
PA
PA
PA
PA
120-4030-000E
Included
in Kit
Qty
3
1
1
2
2
0
0
0
4-2