MAX15112EVKIT# Maxim Integrated, MAX15112EVKIT# Datasheet - Page 10

no-image

MAX15112EVKIT#

Manufacturer Part Number
MAX15112EVKIT#
Description
Power Management IC Development Tools MAX15112 Eval Kit
Manufacturer
Maxim Integrated
Type
Power Switchesr
Series
MAX15112r
Datasheet

Specifications of MAX15112EVKIT#

Rohs
yes
Product
Evaluation Kits
Tool Is For Evaluation Of
MAX15112
Input Voltage
2.7 V to 5.5 V
Output Voltage
0.6 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Output Current
12 A
For Use With
MAX15112
A1, B1, C1,
A2, A3, B2,
B3, C2, C3
B4, C4, D4
D1, D2
PIN
A4
A5
A6
B5
B6
C5
C6
D3
D5
D6
High-Efficiency, 12A, Current-Mode Synchronous
Step-Down Regulator with Integrated Switches
SS/REFIN
PGOOD
NAME
COMP
GSNS
GND
SKIP
BST
N.C
AIN
EN
���������������������������������������������������������������� Maxim Integrated Products 10
LX
FB
IN
Ground Connection. GND is the source terminal of the internal low-side switch. Connect all GND
bumps to a component-side PCB copper ground plane at a single point near the input bypass
capacitor return terminal.
Inductor Connection. Connect LX to the switching side of the inductor. LX is high impedance when
the MAX15112 is in shutdown mode.
Boost Input for the High-Side Switch Driver. Connect a capacitor from BST to LX.
Power-Good Open-Drain Output. PGOOD asserts high when V
deasserts when V
Remote Ground-Sense Input. Connect GSNS to the ground terminal of the load and to the bottom of
the feedback resistors.
Input Power Supply. Bypass IN to GND with at least two 22FF low-ESR ceramic capacitors with suf-
ficient ripple current ratings.
No Connection. Do not connect.
Feedback Input. Connect FB to the center tap of an external resistor divider from the output to the
output capacitor return terminal to set the output voltage from 0.6V to 0.94 x V
Skip-Mode Selector Input. Connect SKIP to EN for skip-mode operation. Connect SKIP to GND or leave
unconnected for continuous mode operation. Do not change the state of SKIP when EN is high.
Soft-Start and External Voltage Reference Input. Connect a capacitor from SS/REFIN to GND to set
the soft-start delay. See the
as an external voltage reference, apply a voltage ranging from 0V to (V
externally control the soft-start time and feedback voltage.
Filtered Input Voltage
Enable Input. Drive EN high to enable the MAX15112. Connect EN to IN for always-on operation.
Error Amplifier Output. Connect the compensation network from COMP to GND. See the
Compensation Design Guidelines
(BUMP ON THE BOTTOM)
TOP VIEW
+
GND
GND
GND
GND
A1
B1
C1
D1
FB
falls below 0.529V (typ).
GND
LX
LX
LX
A2
B2
C2
D2
Setting the Soft-Start Time
AIN
LX
LX
LX
A3
B3
C3
D3
MAX15112
section for more information.
WLP
BST
A4
B4
C4
D4
IN
IN
IN
FUNCTION
PGOOD
SKIP
N.C.
C5
EN
D5
A5
B5
SS/REFIN
COMP
GSNS
section for more information. To use SS/REFIN
A6
FB
B6
C6
D6
FB
is above 0.554V (typ) and
IN
Pin Configuration
- 2.5V) to SS/REFIN to
MAX15112
Pin Description
IN
.

Related parts for MAX15112EVKIT#