IS42S16160D-6TLI ISSI, Integrated Silicon Solution Inc, IS42S16160D-6TLI Datasheet - Page 49
![no-image](/images/manufacturer_photos/0/3/347/issi__integrated_silicon_solution_inc_sml.jpg)
IS42S16160D-6TLI
Manufacturer Part Number
IS42S16160D-6TLI
Description
IC SDRAM 256MBIT 166MHZ 54TSOP
Manufacturer
ISSI, Integrated Silicon Solution Inc
Type
SDRAMr
Specifications of IS42S16160D-6TLI
Format - Memory
RAM
Memory Type
SDRAM
Memory Size
256M (16Mx16)
Speed
166MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
54-TSOP II
Organization
16Mx16
Density
256Mb
Address Bus
15b
Access Time (max)
6.5/5.4ns
Maximum Clock Rate
166MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
-40C to 85C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
180mA
Pin Count
54
Mounting
Surface Mount
Operating Temperature Classification
Industrial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
IS42S83200D, IS42S16160D
Integrated Silicon Solution, Inc. — www.issi.com
Rev. 00D
12/12/07
BURST READ/SINGLE WRITE
The burst read/single write mode is entered by programming
the write burst mode bit (M9) in the mode register to a logic
1. In this mode, all WRITE commands result in the access
of a single column location (burst of one), regardless of
the programmed burst length. READ commands access
columns according to the programmed burst length and
sequence, just as in the normal mode of operation (M9
= 0).
CONCURRENT AUTO PRECHARGE
An access command (READ or WRITE) to another bank
while an access command with auto precharge enabled is
executing is not allowed by SDRAMs, unless the SDRAM
supports CONCURRENT AUTO PRECHARGE. ISSI
READ With Auto Precharge interrupted by a READ
READ With Auto Precharge interrupted by a WRITE
COMMAND
Internal States
ADDRESS
BANK m
BANK n
COMMAND
Internal States
ADDRESS
CLK
DQ
BANK m
BANK n
DQM
CLK
DQ
Page Active
T0
NOP
READ - AP
BANK n,
BANK n
T0
COL a
Page Active
CAS Latency - 3 (BANK n)
BANK n,
READ - AP
COL a
T1
BANK n
Page Active
READ with Burst of 4
T1
NOP
Page Active
READ with Burst of 4
CAS Latency - 3 (BANK n)
T2
NOP
T2
NOP
BANK n,
READ - AP
COL b
BANK m
T3
T3
NOP
D
OUT
CAS Latency - 3 (BANK m)
SDRAMs support CONCURRENT AUTO PRECHARGE.
Four cases where CONCURRENT AUTO PRECHARGE
occurs are defined below.
READ with Auto Precharge
1. Interrupted by a READ (with or without auto precharge):
2.Interrupted by a WRITE (with or without auto precharge):
a
Interrupt Burst, Precharge
A READ to bank m will interrupt a READ on bank n,
begin when the READ to bank m is registered.
A WRITE to bank m will interrupt a READ on bank n
when registered.DQM should be used three clocks prior
to the WRITE command to prevent bus contention. The
CAS latency later. The PRECHARGE to bank n will
PRECHARGE to bank n will begin when the WRITE to
bank m is registered.
T4
WRITE - AP
NOP
BANK m,
BANK m
T4
COL b
D
D
t
OUT
IN
RP - BANK n
READ with Burst of 4
b
a
Interrupt Burst, Precharge
WRITE with Burst of 4
T5
T5
NOP
D
D
NOP
IN
OUT
t
b+1
RP - BANK n
a+1
T6
D
NOP
T6
NOP
IN
D
b+2
OUT
b
DON'T CARE
T7
D
DON'T CARE
NOP
Idle
T7
IN
Write-Back
NOP
D
b+3
Precharge
OUT
t
DPL - BANK m
t
Idle
RP - BANK m
b+1
49