M48Z128Y-70PM1 STMicroelectronics, M48Z128Y-70PM1 Datasheet - Page 12

• Manufacturer Part Number: M48Z128Y-70PM1
• Description: IC NVSRAM 1MBIT 70NS 32DIP
• Manufacturer: STMicroelectronics
• Type: NVSRAMr

Specifications of M48Z128Y-70PM1

• Format - Memory: RAM
• Memory Type: NVSRAM (Non-Volatile SRAM)
• Memory Size: 1M (128K x 8)
• Speed: 70ns
• Interface: Parallel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 32-DIP (600 mil) Module
• Data Bus Width: 8 bit
• Organization: 128 Kb x 8
• Interface Type: Parallel
• Access Time: 70 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Operating Current: 105 mA
• Maximum Operating Temperature: 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: Through Hole
• Word Size: 8b
• Density: 1Mb
• Access Time (max): 70ns
• Operating Supply Voltage (typ): 5V
• Package Type: PMDIP
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Operating Temp Range: 0C to 70C
• Pin Count: 32
• Mounting: Through Hole
• Supply Current: 105mA
• Memory Configuration: 128K X 8
• Nvram Features: Internal Battery
• Supply Voltage Range: 4.5V To 5.5V
• Memory Case Style: PMDIP
• No. Of Pins: 32
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2874-5

M48Z128, M48Z128Y, M48Z128V*
MAXIMUM RATING
Stressing the device above the rating listed in the
“Absolute Maximum Ratings” table may cause
permanent damage to the device. These are
stress ratings only and operation of the device at
these or any other conditions above those indicat-
ed in the Operating sections of this specification is
Table 6. Absolute Maximum Ratings
Note: 1. For DIP package: Soldering temperature not to exceed 260°C for 10 seconds (total thermal budget not to exceed 150°C for longer
DC AND AC PARAMETERS
This section summarizes the operating and mea-
surement conditions, as well as the DC and AC
characteristics of the device. The parameters in
the following DC and AC Characteristic tables are
derived from tests performed under the Measure-
Table 7. Operating and AC Measurement Conditions
Note: Output Hi-Z is defined as the point where data is no longer driven.
12/21
Supply Voltage (V
Ambient Operating Temperature (T
Load Capacitance (C
Input Rise and Fall Times
Input Pulse Voltages
Input and Output Timing Ref. Voltages
T
Symbol
SLD
T
T
V
2. For SO package, standard (SnPb) lead finish: Reflow at peak temperature of 225°C (total thermal budget not to exceed 180°C for
3. For SO package, Lead-free (Pb-free) lead finish: Reflow at peak temperature of 260°C (total thermal budget not to exceed 245°C
V
BIAS
P
T
STG
I
CC
O
IO
(1,2,3)
A
D
than 30 seconds). No preheat above 150°C, or direct exposure to IR reflow (or IR preheat) allowed, to avoid damaging the Lithium
battery.
between 90 to 150 seconds).
for greater than 30 seconds).
CAUTION: Negative undershoots below –0.3V are not allowed on any pin while in the Battery Back-up mode.
CAUTION: Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets.
Ambient Operating Temperature
Storage Temperature (V
Temperature Under Bias
Lead Solder Temperature for 10 seconds
Input or Output Voltages
Supply Voltage
Output Current
Power Dissipation
Parameter
CC
)
L
)
A
)
CC
Off, Oscillator Off)
Parameter
4.75 to 5.5V or 4.5 to 5.5
M48Z128/Y
0 to 70
0 to 3
100
1.5
5
not implied. Exposure to Absolute Maximum Rat-
ing conditions for extended periods may affect de-
vice
STMicroelectronics SURE Program and other rel-
evant quality documents.
ment Conditions listed in the relevant tables. De-
signers should check that the operating conditions
in their projects match the measurement condi-
tions when using the quoted parameters.
M48Z128/Y
M48Z128V
reliability.
M48Z128V
3.0 to 3.6
Refer
0 to 70
0 to 3
1.5
–0.3 to 7.0
–0.3 to 4.6
50
–40 to 85
–10 to 70
–0.3 to 7
5
0 to 70
Value
260
20
1
also
to
Unit
Unit
mA
°C
°C
°C
°C
W
pF
°C
ns
V
V
V
V
V
V
the