EPCS16SI16N Altera, EPCS16SI16N Datasheet - Page 33

• Manufacturer Part Number: EPCS16SI16N
• Description: IC CONFIG DEVICE 16MBIT 16-SOIC
• Manufacturer: Altera
• Series: EPCSr

Specifications of EPCS16SI16N

• Programmable Type: In System Programmable
• Memory Size: 16Mb
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Memory Type: Flash
• Clock Frequency: 20MHz
• Supply Voltage Range: 2.7V To 3.6V
• Memory Case Style: SOIC
• No. Of Pins: 16
• Operating Temperature Range: -40°C To +85°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 544-1240-5; EPCS16SI16

Chapter 3: Serial Configuration Devices (EPCS1, EPCS4, EPCS16, EPCS64, and EPCS128) Data Sheet
Pin Information
Pin Information
Table 3–23. Serial Configuration Device Pin Description (Part 1 of 2)
© December 2009
DATA
ASDI
Name
Pin
2
5
Pin Number
Package
in 8-Pin
SOIC
Altera Corporation
As shown in
16-pin device. The control pins on the serial configuration device are: serial data
output (DATA), active serial data input (ASDI), serial clock (DCLK), and chip select
(nCS).
Figure 3–21
pin-out diagram.
Figure 3–21. Altera Serial Configuration Device 8-Pin SOIC Package Pin-Out Diagram
Figure 3–22
pin-out diagram.
Figure 3–22. Altera Serial Configuration Device 16-Pin SOIC Package Pin-Out Diagram
Note to
(1) These pins can be left floating or connected to V
8
15
Pin Number
in 16-Pin
Package
Figure
SOIC
Table 3–23
3–22:
shows the Altera serial configuration device 8-pin SOIC package and its
shows the Altera serial configuration device 16-pin SOIC package and its
Figure 3–21
Output
Input
Pin Type
lists the serial configuration device's pin descriptions.
and
The DATA output signal transfers data serially out of the serial
configuration device to the FPGA during read/configuration operation.
During read/configuration operations, the serial configuration device
is enabled by pulling nCS low. The DATA signal transitions on the
falling edge of DCLK.
The AS data input signal is used to transfer data serially into the serial
configuration device. It receives the data that should be programmed
into the serial configuration device. Data is latched on the rising edge
of DCLK.
Figure
DATA
DATA
GND
nCS
V
N.C.
N.C.
N.C.
N.C.
nCS
V
V
CC
CC
CC
3–22, the serial configuration device is an 8-pin or
CC
EPCS1, EPCS4,
or EPCS128
or GND, whichever is more convenient on the board.
or EPCS16
1
2
3
4
EPCS64,
2
3
4
5
6
7
8
EPCS16,
1
(1)
(1)
(1)
(1)
14
13
12
11
10
9
16
15
8
7
6
5
(1)
(1)
(1)
(1)
Configuration Handbook (Complete Two-Volume Set)
V
V
DCLK
ASDI
DCLK
ASDI
N.C.
N.C.
N.C.
N.C.
GND
V
CC
CC
CC
Description
3–33