VIPER17HDTR STMicroelectronics, VIPER17HDTR Datasheet - Page 14
![IC OFFLINE CONV PWM OVP 16SOIC](/photos/7/32/73279/viper17hdtr_sml.jpg)
VIPER17HDTR
Manufacturer Part Number
VIPER17HDTR
Description
IC OFFLINE CONV PWM OVP 16SOIC
Manufacturer
STMicroelectronics
Series
VIPer™ plusr
Datasheet
1.VIPER17LDTR.pdf
(31 pages)
Specifications of VIPER17HDTR
Output Isolation
Isolated
Frequency Range
103 ~ 127kHz
Voltage - Input
8.5 ~ 23.5 V
Voltage - Output
800V
Power (watts)
12W
Operating Temperature
-40°C ~ 150°C
Package / Case
16-SOIC (0.154", 3.90mm Width) Exposed Pad
Output Power
1 W
Input Voltage
8.5 V to 23.5 V
Switching Frequency
115 KHz
Mounting Style
SMD/SMT
Duty Cycle (max)
80 %
For Use With
497-9050 - BOARD DEMO BASED ON VIPER17HN497-9007 - BOARD EVAL BASED ON VIPER17497-8513 - BOARD EVAL VIPER17HN 6W SMPS497-8250 - BOARD EVAL FOR VIPER17497-6447 - BOARD EVAL FOR VIPER17L497-6446 - BOARD EVAL FOR VIPER17H
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-7045-2
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
VIPER17HDTR
Manufacturer:
MITSUBISHI
Quantity:
2 944
Part Number:
VIPER17HDTR
Manufacturer:
ST
Quantity:
20 000
Operation descriptions
7
7.1
7.2
14/31
Operation descriptions
VIPER17 is a high-performance low-voltage PWM controller chip with an 800 V, avalanche
rugged power section.
The controller includes: the oscillator with jittering feature, the start up circuits with soft-start
feature, the PWM logic, the current limit circuit with adjustable set point, the second over
current circuit, the burst mode management, the brown-out circuit, the UVLO circuit, the
auto-restart circuit and the thermal protection circuit.
The current limit set-point is set by the CONT pin. The burst mode operation guaranties high
performance in the stand-by mode and helps in the energy saving norm accomplishment.
All the fault protections are built in auto restart mode with very low repetition rate to prevent
IC's over heating.
Power section and gate driver
The power section is implemented with an avalanche ruggedness N-channel MOSFET,
which guarantees safe operation within the specified energy rating as well as high dv/dt
capability. The power section has a BV
of 20 Ω at 25 °C.
The integrated SenseFET structure allows a virtually loss-less current sensing.
The gate driver is designed to supply a controlled gate current during both turn-on and turn-
off in order to minimize common mode EMI. Under UVLO conditions an internal pull-down
circuit holds the gate low in order to ensure that the Power section cannot be turned on
accidentally.
High voltage startup generator
The HV current generator is supplied through the DRAIN pin and it is enabled only if the
input bulk capacitor voltage is higher than V
the HV current generator is ON, the I
capacitor on the V
reduced to 0.6 mA, in order to have a slow duty cycle during the restart phase.
DD
pin. In case of auto restart mode after a fault event, the I
Doc ID 14419 Rev 7
DDch
DSS
current (3 mA typical value) is delivered to the
of 800 V min. and a typical R
DRAIN_START
threshold, 80 V
DC
DS(on)
typically. When
DDch
current is
VIPER17