MCP73871-2CAI/ML Microchip Technology, MCP73871-2CAI/ML Datasheet - Page 21

• Manufacturer Part Number: MCP73871-2CAI/ML
• Description: IC USB/AC BATT CHRGR W/PPM 20QFN
• Manufacturer: Microchip Technology

Specifications of MCP73871-2CAI/ML

• Battery Type: Lithium-Ion (Li-Ion), Lithium-Polymer (Li-Pol)
• Function: Charge Management
• Voltage - Supply: 4.4 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-VFQFN Exposed Pad
• Input Voltage: 6V
• Battery Charge Voltage: 4.5V
• Charge Current Max: 1A
• Battery Ic Case Style: QFN
• No. Of Pins: 20
• No. Of Series Cells: 1
• Product: Charge Management
• Output Voltage: 4.2 V
• Output Current: 50 mA to 1000 mA
• Operating Supply Voltage: 4.5 V to 6 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP73871DM-VPCC - DEMO BOARD FOR MCP73871MCP73871EV - EVALUATION BOARD FOR MCP73871
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.7
The charge cycle is terminated when, during constant
voltage mode, the average charge current diminishes
below a threshold established with the value of a
resistor connected from PROG3 to V
has expired. A 1 ms filter time on the termination
comparator ensures that transient load conditions do
not result in premature charge cycle termination. The
timer period is factory set and can be disabled. Refer to
Section 1.0 “Electrical Characteristics” for timer
period options.
The program resistor and the charge current are
calculated using the following equation:
EQUATION 4-2:
The charge current is latched off and the MCP73871
device enters a charge complete mode. The
recommended PROG3 resistor values are between
5 kΩ and 100 kΩ.
4.8
The MCP73871 device continuously monitors the
voltage at the V
the voltage drops below the recharge threshold,
another charge cycle begins and current is once again
supplied to the battery or load. The recharge threshold
is factory set. Refer to Section 1.0 “Electrical
Characteristics” for recharge threshold options.
© 2009 Microchip Technology Inc.
Where:
Note:
R
PROG
I
REG
Charge Termination
Automatic Recharge
Charge
recharge features avoid constant charging
Li-Ion batteries to prolong life of Li-Ion
batteries while keeping their capacity at
healthy level.
=
=
I
BAT
TERMINATION
pin in the charge complete mode. If
kilo-ohms (kΩ)
milliampere (mA)
termination
=
------------------- -
R
1000V
PROG3
SS
and
or internal timer
automatic
4.9
The MCP73871 device limits the charge current based
on the die temperature. The thermal regulation
optimizes the charge cycle time while maintaining
device reliability.
regulation for the MCP73871 device. Refer to
Section 1.0 “Electrical Characteristics” for thermal
package resistances and Section 6.1.1.2 “Thermal
Considerations” for calculating power dissipation.
.
FIGURE 4-3:
4.10
The MCP73871 device suspends charge if the die
temperature exceeds 150°C. Charging will resume
when the die temperature has cooled by approximately
10°C. The thermal shutdown is a secondary safety
feature in the event that there is a failure within the
thermal regulation circuitry.
4.11
The MCP73871 device continuously monitor battery
temperature during a charge cycle by measuring the
voltage between the THERM and V
50 µA current source provides the bias for most
common
thermistors (NTC). The MCP73871 device compares
the voltage at the THERM pin to factory set thresholds
of 1.24V and 0.25V, typically. Once a voltage outside
the thresholds is detected during a charge cycle, the
MCP73871 device immediately suspends the charge
cycle. The MCP73871 device suspends charge by
turning off the charge pass transistor and holding the
timer value. The charge cycle resumes when the
voltage at the THERM pin returns to the normal range.
1200
1000
800
600
400
200
0
Thermal Regulation
Thermal Shutdown
Temperature Qualification
25
10 kΩ
V
R
DD
PROG
= 5.2V
= 1 kΩ
50
Ambient Temperature (°C)
Figure 4-3
negative-temperature
Thermal Regulation
75
MCP73871
depicts the thermal
100
SS
DS22090B-page 21
pins. An internal
125
coefficient
150