S-8244AAAFN-CEAT2G Seiko Instruments, S-8244AAAFN-CEAT2G Datasheet - Page 20

IC LI-ION BATT PROTECT 8-MSOP

S-8244AAAFN-CEAT2G

Manufacturer Part Number
S-8244AAAFN-CEAT2G
Description
IC LI-ION BATT PROTECT 8-MSOP
Manufacturer
Seiko Instruments
Datasheet

Specifications of S-8244AAAFN-CEAT2G

Function
Over/Under Voltage Protection
Battery Type
Lithium-Ion (Li-Ion)
Voltage - Supply
3.6 V ~ 24 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Product
Li-Ion Protection
Output Voltage
4.45 V
Operating Supply Voltage
3.6 V to 24 V
Supply Current
3 uA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S-8244AAAFN-CEAT2G
Manufacturer:
SEIKO
Quantity:
3 200
Part Number:
S-8244AAAFN-CEAT2G
Manufacturer:
SEIKO/PBF
Quantity:
6 000
Part Number:
S-8244AAAFN-CEAT2G
Manufacturer:
SEIKO/精工
Quantity:
20 000
Part Number:
S-8244AAAFN-CEAT2G
Quantity:
1 970
Part Number:
S-8244AAAFN-CEAT2G
Manufacturer:
SII
Quantity:
19 708
20
BATTERY PROTECTION IC FOR 1-SERIAL TO 4-SERIAL-CELL PACK (SECONDARY PROTECTION)
S-8244 Series
Precautions
• This IC charges the delay capacitor through the delay capacitor pin (ICT pin) immediately when the voltage of one of
• DO NOT connect any of overcharged batteries. Even if only one overcharged battery is connected to this IC, the IC
• In this IC, the output logic of the CO pin is inverted after several milliseconds of internal delay if this IC is under the
• Any position from V1 to V4 can be used when applying this IC for a one to three-cell battery. However, be sure to
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
• SII claims no responsibility for any and all disputes arising out of or in connection with any infringement of the
Battery voltage
CO pin voltage
ICT pin voltage
• The application conditions for the input voltage, output voltage, and load current should not exceed the package
Setting voltage
batteries V1 to V4 reaches the overcharge voltage. Therefore, setting the resistor connected to the VCC pin to any
value greater than the recommended level causes a reduction in the IC power supply voltage because of charge
current of the delay capacitor. This may lead to a malfunction. Set up the resistor NOT to exceed the typical value.
If you change the resistance, please consult us.
detects overcharge, then charge current flows to the delay capacitor through the parasitic diode between pins where
the battery is not connected yet. This may lead to a malfunction. Please perform sufficient evaluation in the case of
use. Depending on an application circuit, even when the fault charge battery is not contained, the connection turn of
a battery may be restricted in order to prevent the output of CO detection pulse at the time of battery connection.
overcharge condition even ICT pin is either “V
products including this IC upon patents owned by a third party.
short circuit between pins not in use (SENSE − VC1, VC1 − VC2, VC2 − VC3, or VC3 − VSS).
power dissipation.
protection circuit.
V
V
V
V
V
SS
CU
CC
SS
SS
CMOS output active “H” and Nch open drain output active “H” products
V
C
CD
ICT
Internal delay
high
V1 battery
C
ICT
Seiko Instruments Inc.
low
SS
− short circuit,” “V
Delay
C
ICT
C
ICT
V2 battery
high
low
DD
− short circuit” or “Open” status.
V3 battery
V4 battery
Rev.6.0
_00

Related parts for S-8244AAAFN-CEAT2G