X9530V14IT2 Intersil, X9530V14IT2 Datasheet - Page 11

• Manufacturer Part Number: X9530V14IT2
• Description: IC LASER DIODE CTRLR 14-TSSOP
• Manufacturer: Intersil
• Type: Laser Diode Controller (Fiber Optic)r

Specifications of X9530V14IT2

• Number Of Channels: 1
• Voltage - Supply: 3 V ~ 5.5 V
• Current - Supply: 9mA
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 14-TSSOP
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

By examining the block diagram in Figure 5, we see
that the maximum current through pin I1 is set by fixing
values for V(VRef) and R1. The output current can
then be varied by changing the data byte at the D/A
converter input.
In general, the magnitude of the current at the D/A
converter output pins (I1, I2) may be calculated by:
where x = 1,2 and N is the decimal representation of
the input byte to the corresponding D/A converter.
The value for the resistor Rx (x = 1,2) determines the
full scale output current that the D/A converter may
sink or source. The full scale output current has a
maximum value of ±1.6 mA, which is obtained using a
resistance of 510Ω for Rx. This resistance may be
connected externally to pin Rx of the X9530, or may
be selected from one of three internal values. Bits
I1FSO1 and I1FSO0 select the full scale output
current setting for I1 as described in “I1FSO1 -
I1FSO0: Current Generator 1 Full Scale Output Set
Bits (Non-volatile)” on page 6. Bits I2FSO1 and
I2FSO0 select the maximum current setting for I2 as
described in “I2FSO1–I2FSO0: Current Generator 2
Full Scale Output Current Set Bits (Non-volatile)” on
The options are summarized in the following tables:
Figure 7. Look-Up Table Addressing
Ix = (V(VRef) / (384 • Rx)) • N
Voltage Input
Reference
Voltage
11
ADC
Register
AD[5:0]
Status
6
X9530
page 7. When an internal resistor is selected for R1 or
R2, then no resistor should be connected externally at
the corresponding pin.
Bits I1DS and I2DS in Control Register 0 select the
direction of the currents through pins I1 and I2
independently (See “I1DS: Current Generator 1
Direction Select Bit (Non-volatile)” on page 4 and
“Control and Status Register Format” on page 5).
D/A Converter Output Current Response
When the D/A converter input data byte changes by
an arbitrary number of bits, the output current changes
from an intial current level (I
(I
D/A Converter Control
The data byte inputs of the D/A converters can be
controlled in three ways:
– 1) With the A/D converter and through the look-up
– 2) Bypassing the A/D converter and directly access-
– 3) Bypassing both the A/D converter and look-up
x
tables (default),
ing the look-up tables,
tables, and directly setting the D/A converter input
byte.
+ ΔI
L2DA[5:0]:
L1DA[5:0]:
Register 2
Register 1
Control
Control
x
). The transition is monotonic and glitchless.
6
D1
D1
D0
D0
Select
L2DAS: bit 6 in
Control register 5
L1DAS: bit 4 in
Control register 5
Select
Out
Out
LUT2 Row
LUT1 Row
Selection bits
Selection bits
x
) to some final level
November 11, 2005
FN8211.1