L6385E STMicroelectronics, L6385E Datasheet - Page 7

• Manufacturer Part Number: L6385E
• Description: IC DRIVER HI/LO SIDE HV 8-DIP
• Manufacturer: STMicroelectronics
• Type: High Voltage High and Low Side Driverr

Specifications of L6385E

• Configuration: Half Bridge
• Input Type: Non-Inverting
• Delay Time: 110ns
• Current - Peak: 400mA
• Number Of Configurations: 1
• Number Of Outputs: 2
• High Side Voltage - Max (bootstrap): 600V
• Voltage - Supply: 17V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Product: Half-Bridge Drivers
• Rise Time: 50 ns
• Fall Time: 30 ns
• Supply Voltage (max): 17 V
• Supply Voltage (min): - 0.3 V
• Supply Current: 250 uA
• Maximum Power Dissipation: 750 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Bridge Type: Half Bridge
• Maximum Turn-off Delay Time: 105 ns
• Maximum Turn-on Delay Time: 110 ns
• Minimum Operating Temperature: - 45 C
• Number Of Drivers: 2
• Output Voltage: 580 V
• For Use With: 497-5492 - EVAL BOARD FOR L6384/L6385/L6386
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-6213-5

L6385E
4
4.1
Bootstrap driver
A bootstrap circuitry is needed to supply the high voltage section. This function is normally
accomplished by a high voltage fast recovery diode
integrated structure replaces the external diode. It is realized by a high voltage DMOS,
driven synchronously with the low side driver (LVG), with in series a diode, as shown in
Figure 4
diode connected in series to the DMOS has been added to avoid undesirable turn on of it.
C
To choose the proper C
capacitor. This capacitor C
The ratio between the capacitors C
It has to be:
e.g.: if Q
300mV.
If HVG has to be supplied for a long time, the C
the leakage losses.
e.g.: HVG steady state consumption is lower than 200µA, so if HVG T
to supply 1µC to C
The internal bootstrap driver gives great advantages: the external fast recovery diode can
be avoided (it usually has great leakage current).
This structure can work only if V
LVG is on. The charging time (T
fulfilled and it has to be long enough to charge the capacitor.
The bootstrap driver introduces a voltage drop due to the DMOS R
Ω). At low frequency this drop can be neglected. Anyway increasing the frequency it must be
taken in to account.
The following equation is useful to compute the drop on the bootstrap DMOS:
where Q
bootstrap DMOS, and T
BOOT
gate
gate
b. An internal charge pump
selection and charging
is 30nC and V
is the gate charge of the external power MOS, R
EXT
. This charge on a 1µF capacitor means a voltage drop of 1V.
BOOT
charge
V
drop
EXT
gate
value the external MOS can be seen as an equivalent
is the charging time of the bootstrap capacitor.
=
is related to the MOS total gate charge:
is 10V, C
charge
OUT
I
ch
EXT
arg
is close to GND (or lower) and in the meanwhile the
(Figure 4
e
) of the C
R
and C
C
EXT
C
dson
EXT
BOOT
is 3nF. With C
→
BOOT
>>>C
=
b) provides the DMOS driving voltage. The
BOOT
V
Q
-------------- -
V
BOOT
drop
gate
gate
EXT
is proportional to the cyclical voltage loss.
(Figure 4
is the time in which both conditions are
selection has to take into account also
=
------------------ - R
T
Q
ch
BOOT
gate
arg
e
dson
a). In the L6385E a patented
= 100nF the drop would be
dson
is the on resistance of the
DSON
ON
(typical value: 125
is 5ms, C
Bootstrap driver
BOOT
has
7/16