VN920SP13TR STMicroelectronics, VN920SP13TR Datasheet

IC DRIVER SINGLE 30A POWERSO-10

VN920SP13TR

Manufacturer Part Number
VN920SP13TR
Description
IC DRIVER SINGLE 30A POWERSO-10
Manufacturer
STMicroelectronics
Type
High Sider
Datasheet

Specifications of VN920SP13TR

Input Type
Non-Inverting
Number Of Outputs
1
On-state Resistance
15 mOhm
Current - Output / Channel
45A
Voltage - Supply
5.5 V ~ 36 V
Operating Temperature
-40°C ~ 150°C
Mounting Type
Surface Mount
Package / Case
PowerSO-10 Exposed Bottom Pad
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Peak Output
-
Lead Free Status / Rohs Status
Not Compliant
Other names
497-2506-2

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
VN920SP13TR
Manufacturer:
ST
0
Part Number:
VN920SP13TR.
Manufacturer:
ST
0
Features
Table 1.
December 2008
VN920SP
CMOS compatible input
Proportional load current sense
Shorted load protection
Under-voltage and over-voltage shutdown
Over-voltage clamp
Thermal shutdown
Current limitation
Protection against loss of ground and loss of
V
Very low standby power dissipation
Reverse battery protected (see
schematic
Type
CC
PowerSO-10
Device summary
Package
)
R
15 m
DS(on)
30 A
I
OUT
Application
Single channel high-side solid-state relay
36 V
V
CC
VN920SP
Rev 3
Tube
The VN920SP is a monolithic device designed in
STMicroelectronics VIPower M0-3 technology.
The VN920SP is intended for driving any type of
load with one side connected to ground. The
active V
against low energy spikes (see ISO7637 transient
compatibility table). Active current limitation
combined with thermal shutdown and automatic
restart protects the device against over-load.
The device integrates an analog current sense
output which delivers a current proportional to the
load current. The device automatically turns off in
the case where the ground pin becomes
disconnected.
Description
CC
Order codes
pin voltage clamp protects the device
PowerSO-10
10
VN920SP13TR
Tape and reel
1
VN920SP
www.st.com
1/26
26

Related parts for VN920SP13TR

VN920SP13TR Summary of contents

Page 1

... The device automatically turns off in the case where the ground pin becomes disconnected. Order codes Tube VN920SP Rev 3 VN920SP 10 1 PowerSO-10 pin voltage clamp protects the device Tape and reel VN920SP13TR 1/26 www.st.com 26 ...

Page 2

Contents Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Electrical ...

Page 3

VN920SP List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4

List of figures List of figures Figure 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 5

VN920SP 1 Block diagram and pin description Figure 1. Block diagram GND INPUT Figure 2. Configuration diagram (top view) Table 2. Suggested connections for unused and not connected pins Connection / pin Floating To ground OVERVOLTAGE V CC DETECTION CLAMP ...

Page 6

... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to Absolute maximum rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics sure program and other relevant quality document. Table 3. ...

Page 7

VN920SP Table 3. Absolute maximum ratings (continued) Symbol Maximum switching energy 0.25mH; R MAX T jstart P Power dissipation T tot T Junction operating temperature j T Case operating temperature c T Storage temperature stg 2.2 Thermal ...

Page 8

Electrical specifications 2.3 Electrical characteristics Values specified in this section are for 8V < V stated. Table 5. Power Symbol Parameter V Operating supply voltage CC V Under-voltage shutdown USD V Over-voltage shutdown OV R On-state resistance ON V Clamp ...

Page 9

VN920SP Table 7. Logic inputs Symbol V Input low-level voltage IL I Low-level input current IL V Input high-level voltage IH I High-level input current IH V Input hysteresis voltage I(hyst) V Input clamp voltage ICL Table 8. Current sense ...

Page 10

Electrical specifications Table 8. Current sense (9V V Symbol Parameter Analog sense output R impedance in VSENSEH over-temperature condition Current sense t DSENSE delay response 1. Current sense signal delay after positive input slope. Table Symbol V ...

Page 11

VN920SP Table 11. Truth table Conditions Normal operation Over-temperature Under-voltage Over-voltage Short circuit to GND Short circuit Negative output voltage clamp Table 12. Electrical transient requirements ISO T/R 7637/1 Test pulse ...

Page 12

Electrical specifications Figure 4. Switching characteristics V OUT dV I SENSE INPUT Figure 5. I OUT I /I OUT SENSE 6500 6000 5500 5000 4500 4000 3500 3000 0 2 12/26 80% /dt OUT (on) 10 90% t ...

Page 13

VN920SP Figure 6. Waveforms INPUT LOAD CURRENT SENSE V CC INPUT LOAD CURRENT SENSE V CC INPUT LOAD CURRENT SENSE INPUT LOAD CURRENT LOAD VOLTAGE SENSE INPUT LOAD VOLTAGE LOAD CURRENT SENSE T j INPUT LOAD CURRENT SENSE NORMAL OPERATION ...

Page 14

Electrical specifications 2.4 Electrical characteristics curves Figure 7. Off-state output current IL(off1) (uA) 2.5 2.25 Off state 2 Vcc= 36V Vin= Vout= 0V 1.75 1.5 1.25 1 0.75 0.5 0.25 0 -50 - (°C ) ...

Page 15

VN920SP Figure 13 LIM case Ilim (A) 100 90 Vcc= 13V -50 - (°C ) Figure 15. Input high-level Vih (V) 3.6 3.4 ...

Page 16

Application information 3 Application information Figure 19. Application schematic + 3.1 GND protection network against reverse battery 3.1.1 Solution 1: resistor in the ground line (R This can be used with any type of load. The following ...

Page 17

VN920SP 3.1.2 Solution 2: diode (D A resistor (R GND inductive load. This small signal diode can be safely shared amongst several different HSDs. Also in this case, the presence of the ground network will produce a shift ( 600mV) ...

Page 18

Application information 3.4 PowerSO-10 maximum demagnetization energy (V Figure 20. PowerSO-10 maximum turn-off current versus inductance 100 150°C single pulse jstart 100°C repetitive pulse jstart ...

Page 19

VN920SP 4 Package and PCB thermal data 4.1 PowerSO-10 thermal data Figure 21. PowerSO-10 PC board Note: Layout condition of R thickness = 2mm, Cu thickness = 35µm, Copper areas: from minimum pad lay-out to 8cm Figure 22. R thj-amb ...

Page 20

Package and PCB thermal data Figure 23. Thermal impedance junction ambient single pulse ZTH (°C/ W) 100 10 1 0.1 0.01 0.0001 0.001 Equation 1 pulse calculation formula : where p Figure 24. ...

Page 21

VN920SP Table 13. Thermal parameters Area / island ( (°C/W) R2 (°C/W) R3 (°C/W) R4 (°C/W) R5 (°C/W) R6 (°C/W) C1 (W.s/°C) C2 (W.s/°C) C3 (W.s/°C) C4 (W.s/°C) C5 (W.s/°C) C6 (W.s/°C) Package and PCB thermal data ...

Page 22

Package and packing information 5 Package and packing information ® 5.1 ECOPACK In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions ...

Page 23

VN920SP Table 14. PowerSO-10 mechanical data Dim (1) L (1) 1. Muar ...

Page 24

Package and packing information 5.3 PowerSO-10 packing information Figure 26. PowerSO-10 suggested pad layout 14.6 - 14 Figure 28. PowerSO-10 tape and reel shipment (suffix “TR”) Tape dimensions According to ...

Page 25

VN920SP 6 Revision history Table 15. Document revision history Date 14-Jul-2004 03-May-2006 17-Dec-2008 Revision 1 Initial release. Minor changes. Current and voltage convention update (page 2). Configuration diagram (top view) and suggested connections for unused and n.c. pins insertion (page ...

Page 26

... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...

Related keywords