MAX16066ETL+ Maxim Integrated Products, MAX16066ETL+ Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX16066ETL+
Manufacturer Part Number
MAX16066ETL+
Description
IC SYSTEM MANAGER 8CH 40-TQFN
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX16065ETM.pdf
(62 pages)
Specifications of MAX16066ETL+
Applications
Power Supply Monitor, Sequencer
Voltage - Supply
2.8 V ~ 14 V
Current - Supply
4.5mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
40-VQFN Exposed Pad, 40-HVQFN, 40-SQFN, 40-DHVQFN
Number Of Voltages Monitored
8
Undervoltage Threshold
2.7 V
Manual Reset
Resettable
Watchdog
Yes
Battery Backup Switching
No
Power-up Reset Delay (typ)
200 us
Supply Voltage (max)
14 V
Supply Voltage (min)
2.8 V
Supply Current (typ)
10 mA
Maximum Power Dissipation
2105 mW
Mounting Style
SMD/SMT
Maximum Operating Temperature
+ 85 C
Chip Enable Signals
No
Internal Hysteresis
Yes
Minimum Operating Temperature
- 40 C
Power Fail Detection
No
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Input
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Figure
12-Channel/8-Channel, Flash-Configurable System
Managers with Nonvolatile Fault Registers
are MON1/MON2, MON3/MON4, MON5/MON6, MON7/
MON8, MON9/MON10, MON11/MON12 with the first
input always being at a higher voltage than the second.
Use differential voltage sensing to eliminate voltage off-
sets or measure supply current. See Figure 4. In differ-
ential mode, the odd-numbered MON_ input measures
the absolute voltage with respect to GND while the result
of the even input is the difference between the odd and
even inputs. See Figure 4 for the typical differential mea-
surement circuit.
The current-sense inputs, CSP/CSM, and a current-
sense amplifier facilitate power monitoring (see Figure
5). The voltage on CSP relative to GND is also monitored
by the ADC when the current-sense amplifier is enabled
with r47h[0]. The conversion results are located in regis-
ters r19h and r1Ah (see Table 10). There are two select-
able voltage ranges for CSP set by r47h[1], see Table
8. Although the voltage can be monitored over SMBus
or JTAG, this voltage has no threshold comparators and
cannot trigger any faults. Regarding the current-sense
amplifier, there are four selectable ranges and the ADC
output for a current-sense conversion is:
where X
r18h, V
sense voltage gain set by r47h[3:2].
18
_____________________________________________________________________________________
SUPPLY
SUPPLY
4. Differential Measurement Connections
POWER
POWER
SENSE
ADC
X
ADC
is the 8-bit decimal ADC result in register
Internal Current-Sense Amplifier
is V
= (V
CSP
SENSE
- V
MON
ODD
x A
CSM,
MAX16065
MAX16066
MON
V
)/1.4V x (2
R
ODD
S
LOAD
and A
MON
V
EVEN
MON
8
is the current-
- 1)
EVEN
I
LOAD
Figure
In addition, there are two programmable current-sense
trip thresholds: primary overcurrent and secondary over-
current. For fast fault detection, the primary overcurrent
threshold is implemented with an analog comparator
connected to the internal OVERC signal. The OVERC
signal can be output on one of the GPIO_s. See the
General-Purpose Inputs/Outputs section for configur-
ing the GPIO_ to output the OVERC signal. The primary
threshold is set by:
where I
threshold set by r47h[3:2], and R
the sense resistor. See Table 8 for a description of r47h.
OVERC depends only on the primary overcurrent thresh-
old. The secondary overcurrent threshold is implement-
ed through ADC conversions and digital comparison set
by r6Ch. The secondary overcurrent threshold includes
programmable time delay options located in r73h[6:5].
Primary and secondary current-sense faults are enabled/
disabled through r47h[0].
GPIO1
inputs/outputs. GPIO1–GPIO8 are configurable as a
manual reset input, a watchdog timer input and output,
logic inputs/outputs, fault-dependent outputs. When pro-
grammed as outputs, GPIO_s are open drain or push-
pull. See Tables 12 and 13 for more detailed information
on configuring GPIO1
R
SENSE
5. Current-Sense Amplifier
–
TH
GPIO8 are programmable general-purpose
LOAD
V
MON
is the current threshold to be set, V
CSM
CSP
*ADJUSTABLE BY r47h[3:2]
General-Purpose Inputs/Outputs
OVERC
I
TH
= V
–
GPIO8.
CSTH
MAX16065
-
+
/R
+
-
SENSE
+
-
SENSE
*V
CSTH
is the value of
*A
V
CSTH
TO ADC MUX
is the