ISL6505CB Intersil, ISL6505CB Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6505CB
Manufacturer Part Number
ISL6505CB
Description
IC MULTIPLE POWER CTRLR 20-SOIC
Manufacturer
Intersil
Datasheet
1.ISL6505CRZ.pdf
(17 pages)
Specifications of ISL6505CB
Applications
Power Supply Controller/Monitor
Voltage - Supply
4.75 V ~ 5.25 V
Current - Supply
6mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
20-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Voltage - Input
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6505CB
Manufacturer:
INTERSIL
Quantity:
43
Company:
Part Number:
ISL6505CB
Manufacturer:
INTERSIL
Quantity:
41
Company:
Part Number:
ISL6505CB
Manufacturer:
INTERSIL
Quantity:
41
Part Number:
ISL6505CB
Manufacturer:
HAR
Quantity:
20 000
Pinouts
Functional Pin Description (Pin numbers for SOIC and QFN)
3V3 (Pin 6 SOIC; Pin 3 QFN)
Connect this pin to the ATX 3.3V output. This pin provides
the output current for the 1V2VID pin, and is monitored for
power quality.
5V (Pin 7 SOIC; Pin 4 QFN)
Connect this pin to the ATX 5V output. This pin is only
monitored for power quality.
5VSB (Pin 20 SOIC; Pin 17 QFN)
Provide a very well de-coupled 5V bias supply for the IC to
this pin by connecting it to the ATX 5V
provides all the chip’s bias as well as the base current for Q2
(see typical application diagram). The voltage at this pin is
monitored for power-on reset (POR) purposes.
GND (Pin 11 SOIC; Pin 8 QFN)
Signal ground for the IC. All voltage levels are measured with
respect to this pin.
S3 and S5 (Pins 9, 10 SOIC; Pins 6, 7 QFN)
These pins switch the IC’s operating state from active (S0,
S1/S2) to S3 and S4/S5 sleep states. These are digital
inputs featuring internal 50µA (typical) current source pull-
ups to 5VSB. Internal circuitry de-glitches these pins for
disturbances lasting as long as 2µs (typically). Additional
circuitry blocks illegal state transitions (such as S4/S5 to S3),
but does allow S3 to S4/S5. Connect S3 and S5
respectively to the computer system’s SLP_S3 and SLP_S5
signals.
3V3DLSB
1V2VID
3V3DL
ISL6505 (20 LEAD WIDE SOIC)
DR1
FB1
EN5
3V3
5V
S3
S5
10
1
2
3
4
5
6
7
8
9
TOP VIEW
6
20
19
18
17
16
15
14
13
12
11
SB
5VSB
VID_CT
VID_PG
SS
LAN
5VDL
5VDLSB
DLA
FAULT
GND
output. This pin
ISL6505
NOTE: The QFN bottom pad is electrically connected to the IC
substrate, at GND potential. It can be left unconnected, or connected
to GND; do NOT connect to another potential.
EN5 (Pin 8 SOIC; Pin 5 QFN)
This digital input selects whether the 5VDL output stays up
or shuts down during the S5 Sleep Mode. It has a 10µA
typical pull-up current source. A logic high (5V) or open will
keep the 5VDL on during S5; a logic low (GND) will shut it off
during S5. NOTE: This pin should be tied low or high (or
open) on the board; it was not designed to be changed
during normal operation.
LAN (Pin 16 SOIC; Pin 13 QFN)
This digital input selects between two modes for the V
regulator. It has a 10µA pull-up current source. A logic high
(5V) or open selects the 10/100 LAN mode, where V
stays on all of the time (active and sleep modes). A logic low
(GND) selects the Gigabit Ethernet mode, where V
only on during active (S0, S1) modes. Note that this
selection is independent of the voltage selection of V
(which is determined by the external resistor divider). NOTE:
This pin should be tied low or high (or open) on the board; it
was not designed to be changed during normal operation.
FAULT (Pin 12 SOIC; Pin 9 QFN)
This digital output pin is used to report the fault condition by
being pulled to 5VSB (pulled to GND if no fault). It is a
CMOS digital output; an external pull-down resistor is NOT
required. In case of an undervoltage on any of the controlled
outputs, on any of the monitored ATX voltages (3V3 or 5V;
not 12V), or in case of an overtemperature event, this pin is
used to report the fault condition.
1V2VID
3V3DL
EN5
3V3
5V
1
2
3
4
5
20
6
ISL6505 (5
19
TOP VIEW
7
18
8
X
5 QFN)
17
9
16
10
15
14
13
12
11
VID_PG
SS
LAN
5VDL
5VDLSB
OUT1
OUT1
OUT1
OUT1
is