ADT7460ARQZ ON Semiconductor, ADT7460ARQZ Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ADT7460ARQZ
Manufacturer Part Number
ADT7460ARQZ
Description
IC REMOTE THRML/FAN CTRLR 16QSOP
Manufacturer
ON Semiconductor
Series
dBCool®r
Specifications of ADT7460ARQZ
Function
Fan Control, Temp Monitor
Topology
ADC, Comparator, Multiplexer, Register Bank
Sensor Type
External & Internal
Sensing Temperature
-40°C ~ 120°C, External Sensor
Output Type
SMBus™
Output Alarm
No
Output Fan
Yes
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-40°C ~ 120°C
Mounting Type
Surface Mount
Package / Case
16-QSOP
Full Temp Accuracy
+/- 3 C
Digital Output - Bus Interface
Serial (3-Wire)
Maximum Operating Temperature
+ 120 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ADT7460ARQZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
ADT7460ARQZ-REEL
Manufacturer:
ST
Quantity:
16
slave address allows the user to avoid conflicts with other
devices sharing the same serial bus, for example, if more
than one ADT7460 is used in a system.
The facility to make hardwired changes to the SMBus
The serial bus protocol operates as follows:
Figure 16. Unpredictable SMBus Address if Pin 8
CARE SHOULD BE TAKEN TO ENSURE THAT PIN 8
(PWM3/ADDR_EN) IS EITHER TIED HIGH OR LOW. LEAVING PIN 8
FLOATING COULD CAUSE THE ADT7460 TO POWERUP WITH AN
UNEXPECTED ADDRESS.
NOTE THAT IF THE ADT7460 IS PLACED INTO ADDRESS SELECT
MODE, PINS 8 AND 9 CAN BE USED AS THE ALTERNATE FUNCTIONS
(PWM3, TACH4/THERM) ONLY IF THE CORRECT CIRCUIT IS MUXED
IN AT THE CORRECT TIME.
1. The master initiates data transfer by establishing a
Figure 15. SMBus Address 0x2D (Pin 9 = 1)
start condition, defined as a high−to−low transition
on the serial data line SDA while the serial clock
line SCL remains high. This indicates that an
address/data stream will follow. All slave
peripherals connected to the serial bus respond to
the star condition and shift in the next eight bits,
consisting of a 7−bit address (MSB first) plus a
R/W bit, which determine the direction of the data
transfer, that is, whether data is written to or read
from the slave device.
The peripheral whose address corresponds to the
transmitted address responds by pulling the data
line low during the low period before the ninth
clock pulse, known as the Acknowledge bit. All
other devices on the bus now remain idle while the
selected device waits for data to be read from or
written to it. If the R/W bit is a 0, the master writes
PWM3/ADDR_EN
PWM3/ADDR_EN
ADT7460
ADT7460
ADDR_SEL
ADDR_SEL
is Unconnected
9
8
9
8
V
CC
NC
10kΩ
10kΩ
DO NOT LEAVE ADDR_EN
V
UNCONNECTED. CAN
CAUSE UNPREDICTABLE
ADDRESSES
CC
ADDRESS = 0x2D
http://onsemi.com
ADT7460
10
serial bus in one operation, but it is not possible to mix read
and write in one operation because the type of operation is
determined at the beginning and cannot subsequently be
changed without starting a new operation.
either one or two bytes, and read operations contain one
byte.
data from it, the address pointer register must be set so that
the correct data register is addressed. Then data can be
written in that register or read from it. The first byte of a
write operation always contains an address that is stored in
the address pointer register. If data is to be written to the
device, the write operation contains a second data byte that
is written to the register selected by the address pointer
register.
over the bus followed by R/W being set to 0. This is followed
by two data bytes. The first data byte is the address of the
internal data register to be written to, which is stored in the
address pointer register. The second data byte is the data to
be written to the internal data register.
Any number of bytes of data may be transferred over the
In the case of the ADT7460, write operations contain
To write data to one of the device data registers or read
This is illustrated in Figure 17. The device address is sent
2. Data is sent over the serial bus in sequences of
3. When all data bytes have been read or written,
to the slave device. If the R/W bit is a 1, the
master reads from the slave device.
nine clock pulses, eight bits of data followed by an
Acknowledge bit from the slave device.
Transitions on the data line must occur during the
low period of the clock signal and remain stable
during the high period, as a low−to−high transition
when the clock is high may be interpreted as a stop
signal. The number of data bytes that can be
transmitted over the serial bus in a single read or
write operation is limited only by what the master
and slave devices can handle.
stop conditions are established. In write mode, the
master pulls the data line high during the 10th
clock pulse to assert a stop condition. In read
mode, the master device overrides the
acknowledge bit by pulling the data line high
during the low period before the ninth clock pulse.
This is known as No Acknowledge. The master
then takes the data line low during the low period
before the 10th clock pulse, then high during the
10th clock pulse to assert a stop condition.