MIC3172YN Micrel Inc, MIC3172YN Datasheet - Page 9

IC REG SW 100KHZ 1.25A 8-DIP

MIC3172YN

Manufacturer Part Number
MIC3172YN
Description
IC REG SW 100KHZ 1.25A 8-DIP
Manufacturer
Micrel Inc
Type
Step-Down (Buck), Step-Up (Boost), Inverting, Cukr
Datasheets

Specifications of MIC3172YN

Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Current - Output
1.25A
Frequency - Switching
100kHz
Voltage - Input
3 ~ 40 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Power - Output
302mW
Primary Input Voltage
40V
No. Of Outputs
1
Output Current
3A
No. Of Pins
8
Operating Temperature Range
-40°C To +85°C
Supply Voltage Range
3V To 40V
Termination Type
Through Hole
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
576-2255
MIC3172YN
MIC2172/3172
Applications Information
Using the MIC3172 Enable Control (New Designs)
For new designs requiring enable/shutdown control, connect
EN to a TTL or CMOS control signal (figure 3). The very low
driver current requirement ensures compatibility regardless
of the driver or gate used.
Using the MIC3172 in LT1172 Applications
The MIC3172 can be used in most original LT1172 applica-
tions by adapting the MIC3172’s enable/shutdown feature to
the existing LT1172 circuit.
Unlike the LT1172 which can be shutdown by reducing the
voltage on pin 2 (V
dedicated enable/shutdown pin. To replace the LT1172 with
the MIC3172, determine if the LT1172’s shutdown feature is
used.
Circuits without Shutdown
If the shutdown feature is not being used, connect EN to V
to continuously enable the MIC3172 or use an MIC2172 with
SYNC open (figure 4).
Circuits with Shutdown
If shutdown was used in the original LT1172 application,
connect EN to a logic gate that produces a TTL logic-level
output signal that matches the shutdown signal. The MIC3172
will be enabled by a logic-high input and shutdown with a
logic-low input (figure 5). The actual components performing
the functions of U1 and Q1 may vary according to the original
application.
April 2005
V
IN
N/C
Figure 3. MIC3172 TTL Enable/Shutdown
Figure 5. Adapting to the LT1172 Socket
Figure 4. MIC2172/3172 Always Enabled
Shutdown
4
Shutdown
Enable
Enable
SYNC
MIC2172
V
C
IN
) below 0.15V, the MIC3172 has a
add
connection
Logic
Gate
U1
Existing
U1
Logic
Gate
4
V
4
IN
EN
EN
Existing
Q1
VN2222
or equiv.
MIC3172
MIC3172
4
COMP
EN
R1
C1
MIC3172
V
IN
IN
9
By using the MIC3172, U1 and Q1 shown in figure 5 can be
eliminated, reducing the total components count.
Synchronizing the MIC2172
Using several unsynchronized switching regulators in the
same circuit will cause beat frequencies to appear on the
inputs and outputs. These beat frequencies can be very low
making them difficult to filter.
Micrel’s MIC2172 can be synchronized to a single master
frequency avoiding the possibility of undesirable beat fre-
quencies in multiple regulator circuits. The master frequency
can be an external oscillator or a designated master MIC2172.
The master frequency should be 1.05 to 1.20 times the
slave’s 100kHz nominal frequency to guarantee synchroni-
zation.
Figure 6 shows a typical application where several MIC2172s
operate from the same supply voltage. U1’s oscillator fre-
quency is increased above U2’s and U3’s by connecting a
resistor from SYNC to ground. U2-SYNC and U3-SYNC are
capacitively coupled to the master’s output (V
slaves lock to the negative (falling edge) of U1’s output
waveform.
Care must be exercised to insure that the master MIC2172 is
always operating in continuous mode.
10kΩ
Figure 6. Master/Slave Synchronization
4
Figure 7. External Synchronization
SYNC
External
Signal
MIC2172
Master
U1
Additional
Slaves
V
SW
5
4
4
Additional
Slaves
SYNC
SYNC
MIC2172
MIC2172
Slave
Slave
U1
U2
4
4
SYNC
SYNC
V
V
SW
SW
MIC2172
MIC2172
Slave
Slave
5
5
U2
U3
M9999-042205
Micrel, Inc.
V
V
SW
SW
SW
). The
5
5

Related parts for MIC3172YN