MAX850ESA+ Maxim Integrated Products, MAX850ESA+ Datasheet - Page 8

• Manufacturer Part Number: MAX850ESA+
• Description: IC PWR SUP CHRG PUMP 8SOIC
• Manufacturer: Maxim Integrated Products
• Type: Switched Capacitor (Charge Pump), Invertingr

Specifications of MAX850ESA+

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: -4.1V, -05 ~ -9 V
• Current - Output: 5mA
• Frequency - Switching: 100kHz
• Voltage - Input: 4.5 ~ 10 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Power - Output: 471mW
• Function: Inverting
• Output Voltage: - 4.1 V or - 0.5 V to - 9 V
• Output Current: 5 mA
• Supply Current: 2 mA
• Maximum Operating Temperature: + 85 C
• Input Voltage: 4.5 V to 10 V
• Maximum Power Dissipation: 471 mW
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Switching Frequency: 100 KHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Low-Noise, Regulated, Negative
Charge-Pump Power Supplies for GaAsFET Bias
sensitivity and interference. The clock must be a square wave
between 40% and 60% duty cycle. The maximum clock fre-
quency is 250kHz, and the minimum frequency is 50kHz.
Good layout is important, primarily for good noise perfor-
mance.
1) Mount all components as close together as possible.
2) Keep traces short to minimize parasitic inductance
3) Use a ground plane.
Accurately measuring the output noise and ripple is a chal-
lenge. Brief differences in ground potential between the
MAX850–MAX853 circuit and the oscilloscope (which result
from the charge pump’s switching action) cause ground
currents in the probe’s wires, inducing sharp voltage spikes.
For best results, measure directly across the output capaci-
tor (C4). Do not use the ground lead of the oscilloscope
probe; instead, remove the probe’s tip cover and touch the
ground ring on the probe directly to C4’s ground terminal.
You can also use a Tektronix chassis mount test jack (part
no. 131-0258) to connect your scope probe directly. This
direct connection gives the most accurate noise and rip-
ple measurement.
________________________________________________________Package Information
8
and capacitance. This includes connections to FB.
______________________________________________________________________________________
e
Noise and Ripple Measurement
D
B
A1
Layout and Grounding
E
A
H
0.127mm
0.004in.
C
h x 45˚
TRANSISTOR COUNT: 164
SUBSTRATE CONNECTED TO IN
___________________Chip Topography
NEGOUT
L
C1+
C1-
SHDN (MAX850/853)
SHDN (MAX851)
OSC (MAX852)
(2.159mm)
0.085"
DIM
A1
C
D
H
A
B
E
e
h
L
0.053
0.004
0.014
0.007
0.189
0.150
0.228
0.010
0.016
SMALL-OUTLINE
MIN
0˚
8-PIN PLASTIC
0.050 BSC
INCHES
PACKAGE
0.069
0.010
0.019
0.010
0.197
0.157
0.244
0.020
0.050
MAX
8˚
IN
GND
FB (MAX850–852)
CONT (MAX853)
OUT
MILLIMETERS
1.35
0.10
0.35
0.19
4.80
3.80
5.80
0.25
0.40
MIN
0˚
1.27 BSC
(3.226mm)
0.127"
MAX
21-325A
1.75
0.25
0.49
0.25
5.00
4.00
6.20
0.50
1.27
8˚