HCPL-4534 Avago Technologies US Inc., HCPL-4534 Datasheet

Page 1

... UL Recognized – 3750 V rms for 1 minute (5000 V rms for 1 minute for Option 020) per UL1577 CSA Approved IEC/EN/DIN EN 60747-5-2 –V = 630 Vpeak for HCPL-4534 0ption 060 IORM – 560 Vpeak for HCPL-0534 0ption 060 IORM • Single channel version available (4502/3, 0452/3) • ...

Page 2

... The lead profile is designed to be compatible with standard surface mount processes. The HCPL-4534/0534 is designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough output current for 1 TTL load and a 5.6 kΩ pull-up resistor. CTR of the HCPL- 4534/0534 is 19% minimum ...

Page 3

... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-4534 to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/ EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-4534 to order product of 300mil DIP package in tube packaging and non RoHS compliant ...

Page 4

... V F1 – – USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED. Package Outline Drawings 8-Pin DIP Package (HCPL-4534) 9.65 ± 0.25 (0.380 ± 0.010 TYPE NUMBER A XXXXZ YYWW 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± ...

Page 5

... Package Outline Drawings, continued 8-Pin DIP Package with Gull Wing Surface Mount Option 300 or 500 (HCPL-4534) 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). ...

Page 6

Solder Reflow Thermal Profile 300 PREHEATING RATE 3 ° °C/–0.5 °C/SEC. REFLOW HEATING RATE 2.5 °C ± 0.5 °C/SEC. 200 160 °C 150 °C 140 °C 3 ° °C/–0.5 °C 100 ROOM TEMPERATURE ...

Page 7

Insulation and Safety Related Specifications Parameter Symbol Minimum External L(101) Air Gap (External Clearance) Minimum External L(102) Tracking (External Creepage) Minimum Internal Plastic Gap (Internal Clearance) Minimum Internal Tracking (Internal Creepage) Tracking Resistance CTI (Comparative Tracking Index) Isolation Group Option ...

Page 8

... S 8 Symbol V IORM IOTM S,INPUT P S,OUTPUT R S and I on ambient temperature 125 150 175 200 Characteristic HCPL-4534 HCPL-0534 I-IV I-IV I-III I-III I-II 55/100/21 55/100/ 630 567 1181 1050 945 840 6000 4000 175 175 230 230 600 600 9 9 > 10 > ...

Page 9

Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Average Forward Input Current (each channel) Peak Forward Input Current (each channel) (50% duty cycle pulse width) Peak Transient Input Current (each channel) (≤ 1 µs pulse width, 300 pps) ...

Page 10

Electrical Specifications (DC) Over recommended temperature (T Parameter Sym. Min. Current Transfer CTR 19 Ratio 15 Logic Low V OL Output Voltage Logic High I OH Output Current Logic Low I CCL Supply Current Logic High I CCH Supply Current ...

Page 11

... I-I Insulation Leakage Current Resistance R I-I (Input-Input) Capacitance C HCPL-4534 I-I (Input-Input) HCPL-0534 * All typicals 25° The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled “ ...

Page 12

... T = 25° 5 – OUTPUT VOLTAGE – Figure 1. DC and pulsed transfer characteristics. HCPL-2530 fig 1 1.1 1.0 0.9 NORMALIZED 0 0 25°C A 0.7 HCPL-2530/0530 HCPL-2531/0531/4534/0534 0.6 -60 -40 - 100 T – TEMPERATURE – °C A Figure 4. Current transfer ratio vs. temperature. HCPL-2530 Figure 4 0.30 = 100 Ω 25° 0.20 ...

Page 13

... DUTY CYCLE 1/f < 100 µ MONITOR 0.1 µ – + PULSE GEN. www.avagotech.com 0.1 µ 0.1µ ° 1 0.6 0.4 0.2 0 – LOAD RESISTANCE – kΩ L Figure 11. Propagation delay time vs. load resistance. HCPL-2530 Figure 11 t PLH t PHL ...