HCPL-4534 Avago Technologies US Inc., HCPL-4534 Datasheet - Page 11

• Manufacturer Part Number: HCPL-4534
• Description: OPTOCOUPLER 2CH 1MBS 8-DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-4534

• Input Type: DC
• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 8mA
• Propagation Delay High - Low @ If: 200ns @ 16mA
• Current - Dc Forward (if): 25mA
• Output Type: Open Collector
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Forward Diode Current: 16 mA
• Output Device: Phototransistor
• Configuration: 2 Channel
• Current Transfer Ratio: 24 %
• Maximum Baud Rate: 1 MBps
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 25 mA
• Maximum Power Dissipation: 45 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 55 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Package Characteristics
*
** The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
Notes:
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for 1 second (leakage de-
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for 1 second (leakage de-
12. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
13. Derate linearly above 90°C free-air temperature at a rate of 3.0 mW/ ° C for the SOIC-8 package.
11
Parameter
Input-Output
Momentary With-
stand Voltage**
Resistance
(Input-Output)
Capacitance
(Input-Output)
Input-Input
Insulation
Leakage Current
Resistance
(Input-Input)
Capacitance
(Input-Input)
1. Each channel.
2. CURRENT TRANSFER RATIO is defined as the ratio of output collector current, I
3. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
4. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
5. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
6. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
7. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and the 6.1 kΩ pull-up resistor.
8. The frequency at which the ac output voltage is 3 dB below the low frequency asymptote.
9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
All typicals at T
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your
equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage, ” publication
number 5963-2203E.
mode pulse, V
Low level is the maximum tolerable (negative) dV
will remain in a Logic Low state (i.e., V
tection current limit, I
tection current limit, I
A
CM
= 25°C.
, to assure that the output will remain in a Logic High state (i.e., V
I-O
I-O
Sym.
V
R
C
I
R
C
I-I
ISO
I-O
I-I
I-O
I-I
≤5 µA).
≤5 µA).
Device
with
Option 020
HCPL-4534
HCPL-0534
O
< 0.8 V).
CM
Min.
3750
5000
/dt on the falling edge of the common mode pulse signal, V
Typ.*
10
0.6
0.005
10
0.03
0.25
12
11
Max.
O
, to the forward LED input current, I
O
> 2.0 V). Common mode transient immunity in a Logic
Units
V rms
Ω
pF
µA
Ω
pF
CM
/dt on the rising edge of the common
Test Conditions
V
T
V
RH < 50%,
t = 1 min.,
RH ≤45%
t = 5 s
f = 1 MHz,
RH ≤45%,
t = 5 s,
f = 1 MHz
A
I-I
I-O
= 25°C
= 500 Vdc
= 500 Vdc,
CM
, to assure that the output
F
, times 100%.
Fig.
Note
3, 10
3, 11
3
12
4
4
4