LQ104S1DG21 Sharp Microelectronics, LQ104S1DG21 Datasheet
![LCD TFT 10.4" 800X600 SVGA](/photos/7/92/79296/lq104s1dg21_sml.jpg)
LQ104S1DG21
Specifications of LQ104S1DG21
Related parts for LQ104S1DG21
LQ104S1DG21 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ104S1DG21 TFT-LCD Module Spec. Issue Date: September 27, 2005 AVC Liquid Crystal Displays Group No: LD-14304D ...
Page 2
...
Page 3
LD-14304 Apr. 10.2002 - LD-14304A Apr. 22.2003 1.Application Added the sentence, “ (This specification is only )” 4-1. TFT-LCD panel driving Deleted Used connector:DF9MA-41P-1V(Hirose Electric Co., Ltd.) 6-1. TFT-LCD panel driving Current dissipation Vcc=3.3V Icc typ ...
Page 4
LD-14304B 2004.1 LD-14304C Added Note) Insulate the high 12.Packing form Product Country Added TAIWAN 14 Others 1)Label: Added the figure of module label (Taiwan product) Added the figure of packing box label(Taiwan product) 6-2. Backlight ...
Page 5
... Application This specifications applies to color TFT-LCD module, LQ104S1DG21. (This specification is only applied for the module which has letter "A" at the end of the lot number of the module.) These specifications sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 6
Mechanical Specifications Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1 excluding backlight cables. Outline dimensions is shown in Fig.1 4. Input Terminals 4-1. TFT-LCD panel driving ...
Page 7
Pin No. Symbol 1 GND GND 4 Hsync 5 Vsync 6 GND 7 GND 8 GND GND GND 17 GND 18 GND 19 ...
Page 8
Note3 R/L=High U/D=Low Please do not use this terminal by “open”. Note4 R/L=High U/D=High Please do not use this terminal by “open”. 4-2. Backlight driving Connector name :CN2 CN3 Pin no. Symbol 1 Power supply for lamp HIGH 2 NC ...
Page 9
Electrical Characteristics 6-1.TFT-LCDpaneldriving Parameter Power Supply voltage Supply Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (low) Input current (High) NOTE 1 Vcc-turn-on conditions Vcc-dip conditions Vcc-dip condition should also follow The Vcc-turn-on ...
Page 10
Backlight driving The backlight system is an edge-lighting type with twin CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. (It is usually required to measure under the following condition. condition I ...
Page 11
Timing Characteristics of input signals Timing diagrams of input signal are shown in Fig.2. 7-1. Timing characteristics Parameter Clock Frequency High time Low time Duty ratio Data Setup time Hold time Horizontal Cycle sync. signal Pulse width Vertical Cycle ...
Page 12
...
Page 13
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale R0 R1 Gray Scale Black 0 0 Blue 0 0 Green 0 0 Cyan 0 0 Red 1 1 Magenta 1 1 Yellow 1 ...
Page 14
Optical Characteristics Parameter Viewing Horizontal Angle Vertical Range Contrast ratio Response Rise Time Decay Chromaticity of White Luminance of white White Unifomity Viewing Angle Horizontal range as a Vertical Brightness Definition The measurement shall be executed 30 minutes after ...
Page 15
Note1 Definitions of viewing angle range: Note2 Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) Note3 Definition of response time: The response time is defined as the following figure and shall be measured ...
Page 16
Display Quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. 11 Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable ...
Page 17
... GND to 4 place = un-connect, Vcc / Vsignal = typ. Model No. Lot No. Quantity Model No. TYPE Lot No.(DATE) QUANTITY Quantity DATE User Model No. Sharp internal Model No. for LCD modules in the carton will be shown here. Remark 2 ) 8kV ) 15kV VCCI ClassB SHARP LQ104S1DG21 41 Z00001 G A MADE IN TAIWAN LQ104S1DG21 LQ104S1DG21G 20 pcs 2004.01.9 ...
Page 18
Internal Use Only . . R.C. RoHS Compliance means these parts have corresponded with the RoHS directive. 2) Adjusting volume have been set optimally before shipment not change any adjusted value. If adjusted value is changed, the specification ...
Page 19
...
Page 20
...
Page 21
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...
Page 22
... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...