AFCT-5961NLZ Avago Technologies US Inc., AFCT-5961NLZ Datasheet - Page 11
![TXRX OPT SM SONET OC3/SDH 2X5](/photos/22/52/225255/3762219_sml.jpg)
AFCT-5961NLZ
Manufacturer Part Number
AFCT-5961NLZ
Description
TXRX OPT SM SONET OC3/SDH 2X5
Manufacturer
Avago Technologies US Inc.
Series
METRAKr
Datasheet
1.AFCT-5961TGZ.pdf
(16 pages)
Specifications of AFCT-5961NLZ
Applications
General Purpose
Data Rate
155Mbps
Wavelength
1300nm
Voltage - Supply
3.1 V ~ 3.5 V
Connector Type
LC Duplex
Mounting Type
Through Hole
Data Rate Max
0.155Gbps
Supply Voltage
3.3V
Wavelength Typ
1300nm
Leaded Process Compatible
Yes
Optical Fiber Type
TX/RX
Data Transfer Rate
155Mbps
Optical Rise Time
2/2.2ns
Optical Fall Time
2/2.2ns
Operating Temperature Classification
Commercial
Peak Wavelength
1360nm
Package Type
DIP With Connector
Operating Supply Voltage (min)
3.1V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.5V
Output Current
50mA
Operating Temp Range
-5C to 70C
Mounting
Snap Fit To Panel
Pin Count
10
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Regulatory Compliance
The Regulatory Compliance for transceiver performance
is shown in Table 1. The overall equipment design will
determine the certification level. The transceiver per-
formance is offered as a figure of merit to assist the
designer in considering their use in equipment designs.
Electrostatic Discharge (ESD)
There are two design cases in which immunity to ESD
damage is important.
The first case is during handling of the transceiver prior
to mounting it on the circuit board. It is important to
use normal ESD handling precautions for ESD sensitive
devices. These precautions include using grounded
wrist straps, work benches, and floor mats in ESD con-
trolled areas.
The second case to consider is static discharges to the
exterior of the equipment chassis containing the trans-
ceiver parts. To the extent that the LC connector recep-
tacle is exposed to the outside of the equipment chassis
it may be subject to whatever system-level ESD test
criteria that the equipment is intended to meet.
Table 1: Regulatory Compliance - Targeted Specification
11
Feature
Electrostatic Discharge
(ESD) to the Electrical Pins
Electrostatic Discharge
(ESD) to the LC Receptacle
Electromagnetic Interference
(EMI)
Immunity
Laser Eye Safety
and Equipment
Type Testing
Component
Recognition
Test Method
MIL-STD-883
Method 3015
Variation of
IEC 61000-4-2
FCC Class B
Variation of
IEC 61000-4-3
FDA CDRH 21-CFR 1040
Class 1
IEC 60825-1
Amendment 2 2001-01
Underwriters Laboratories and Canadian Standards
Association Joint Component Recognition for Infor-
mation Technology Equipment Including Electrical
Business Equipment.
Electromagnetic Interference (EMI)
Most equipment designs utilizing these high-speed
transceivers from Avago Technologies will be required
to meet FCC regulations in the United States, CENELEC
EN55022 (CISPR 22) in Europe and VCCI in Japan. Refer
to EMI section (page 9) for more details.
Immunity
Transceivers will be subject to radio-frequency electro-
magnetic fields following the IEC 61000-4-3 test method.
Eye Safety
These laser-based transceivers are classified as AEL Class
I (U.S. 21 CFR(J) and AEL Class 1 per EN 60825-1 (+A11).
They are eye safe when used within the data sheet
limits per CDRH. They are also eye safe under normal
operating conditions and under all reasonably foresee-
able single fault conditions per EN60825-1. Avago Tech-
nologies has tested the transceiver design for compli-
ance with the requirements listed below under normal
operating conditions and under single fault conditions
where applicable. TUV Rheinland has granted certifica-
tion to these transceivers for laser eye safety and use in
EN 60825-2 applications. Their performance enables the
transceivers to be used without concern for eye safety
up to 3.5 V transmitter V
Performance
Class 1 (>500 V).
Tested to 8 kV contact discharge.
Margins are dependent on customer
board and chassis designs.
Typically show no measurable effect
from a 10 V/m field swept from 27 to
1000 MHz applied to the transceiver
without a chassis enclosure.
Accession Number:
9521220-124
License Number:
933/21203530/03
UL File Number: E173874
CC
.