SW003A0A91-SR Lineage Power, SW003A0A91-SR Datasheet - Page 13
![CONVERT DC/DC 5V 15W OUT SMD TR](/photos/8/59/85955/mfg_sw00_series_sml.jpg)
SW003A0A91-SR
Manufacturer Part Number
SW003A0A91-SR
Description
CONVERT DC/DC 5V 15W OUT SMD TR
Manufacturer
Lineage Power
Series
SWr
Type
Isolated with Remote On/Offr
Datasheet
1.SW003A5F91-SRZ.pdf
(24 pages)
Specifications of SW003A0A91-SR
Output
5V
Number Of Outputs
1
Power (watts)
15W
Mounting Type
Surface Mount
Voltage - Input
36 ~ 75V
Package / Case
6-DIP SMD Module
1st Output
5 VDC @ 3A
Size / Dimension
1.10" L x 0.96" W x 0.34" H (27.9mm x 24.4mm x 8.6mm)
Power (watts) - Rated
15W
Operating Temperature
-40°C ~ 85°C
Efficiency
85.5%
Approvals
CE, CSA, UL, VDE
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
3rd Output
-
2nd Output
-
4th Output
-
Lead Free Status / Rohs Status
No RoHS Version Available
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SW003A0A91-SR
Manufacturer:
LINEAGEPO
Quantity:
20 000
Data Sheet
October 5, 2009
Test Configurations
Figure 43. Input Reflected Ripple Current Test Setup.
Figure 44. Output Ripple and Noise Test Setup.
Figure 45. Output Voltage and Efficiency Test Setup.
LINEAGE
Efficiency
NOTE: All voltage measurements to be taken at the module
TO OSCILLOSCOPE
NOTE: Measure input reflected ripple current with a simulated
R
R
V
V
NOTE: All voltage measurements to be taken at the module
distribution
distribution
O
O
(+)
( – )
POWER
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
source inductance (L
possible battery impedance. Measure current as shown
above.
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
R
R
contact
contact
η =
@ 20°C 100kHz
E.S.R.<0.1Ω
C
COPPER STRIP
1uF .
S
12μH
L
V
220μF
TEST
IN
V
V
Vin+
Vin-
O
IN
TEST
. I
. I
GROUND PLANE
18-36Vdc & 36-75Vdc Input; 3.3-15Vdc Output; 1-3.5A Output Current
) of 12μH. Capacitor C
O
IN
10uF
Vout+
Vout-
V
x 100 %
O
33μF
SCOPE
CURRENT PROBE
R
R
contact
contact
Vin+
S
Vin-
RESISTIVE
LOAD
offsets
R
R
distribution
distribution
R
LOAD
SW/SC001/003 Series DC-DC Power Module:
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance source. Highly inductive source
impedance can affect the stability of the power module.
For the test configuration in Figure 43, a 33μF
electrolytic capacitor (ESR<0.7Ω at 100kHz), mounted
close to the power module helps ensure the stability of
the unit. Consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL 60950-1-3, CSA C22.2 No. 60950-00, and VDE
0805 (IEC60950, 3
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75Vdc), for the module’s output to be considered as
meeting the requirements for safety extra-low voltage
(SELV), all of the following must be true:
Note: Do not ground either of the input pins of the
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
For input voltages exceeding –60 Vdc but less than or
equal to –75 Vdc, these converters have been evaluated
to the applicable requirements of BASIC INSULATION
between secondary DC MAINS DISTRIBUTION input
(classified as TNV-2 in Europe) and unearthed SELV
outputs.
The input to these units is to be provided with a
maximum 3A time-delay fuse in the ungrounded lead.
The input source is to be provided with reinforced
insulation from any other hazardous voltages,
including the ac mains.
One V
or both the input and output pins are to be kept
floating.
The input pins of the module are not operator
accessible.
Another SELV reliability test is conducted on the
whole system (combination of supply source and
subject module), as required by the safety agencies,
to verify that under a single fault, hazardous
voltages do not appear at the module’s output.
module without grounding one of the output pins.
This may allow a non-SELV voltage to appear
between the output pins and ground.
IN
pin and one V
rd
Edition).
OUT
pin are to be grounded,
13